メインコンテンツにスキップ

Logitech Dual Action Triggers Repair

必要な工具と部品

  1. Logitech Dual Action Triggers Repair, Logitech Dual Action Triggers Repair: 手順 1、 1の画像 1
    • To get into the controller, you will need to unscrew the 7 screws on the back.

    • You will have to remove the bottom oval sticker to reveal the screw circled in red.

  2. Logitech Dual Action Triggers Repair: 手順 2、 2の画像 1 Logitech Dual Action Triggers Repair: 手順 2、 2の画像 2
    • With the screws removed, turn the controller upside down and separate the front end from the back end.

    • It is likely that the buttons will fall out of place, so as you open the controller, try to keep track of where the pieces go.

  3. Logitech Dual Action Triggers Repair: 手順 3、 1の画像 1
    • There should be 4 circular buttons labeled 1-4, 4 smaller circular buttons for the D-Pad, and 3 oval shaped buttons.

  4. Logitech Dual Action Triggers Repair: 手順 4、 3の画像 1 Logitech Dual Action Triggers Repair: 手順 4、 3の画像 2 Logitech Dual Action Triggers Repair: 手順 4、 3の画像 3
    • In the center of the controller, pull upwards on the USB cord.

    • Be careful not to pull hard enough to yank the wires connecting to the logic board.

    • With the wire out of the way, remove the screw it exposed. This will disconnect the logic board from the controller.

  5. Logitech Dual Action Triggers Repair: 手順 5、 3の画像 1 Logitech Dual Action Triggers Repair: 手順 5、 3の画像 2 Logitech Dual Action Triggers Repair: 手順 5、 3の画像 3
    • To remove the triggers, push upwards from the back on them.

    • Once far enough, detach the logic board from the back cover piece and the triggers.

  6. Logitech Dual Action Triggers Repair: 手順 6、 2の画像 1 Logitech Dual Action Triggers Repair: 手順 6、 2の画像 2
    • If the wire is unplugged solely from the logic board, you can fasten it back into its place.

    • Look at the second picture to see where the wires go.

  7. Logitech Dual Action Triggers Repair: 手順 7、 3の画像 1 Logitech Dual Action Triggers Repair: 手順 7、 3の画像 2 Logitech Dual Action Triggers Repair: 手順 7、 3の画像 3
    • Unscrew the screw on the trigger to remove the back cover.

    • Once removed, carefully pull the back cover off.

  8. Logitech Dual Action Triggers Repair: 手順 8、 1の画像 1
    • The 3 wires are soldered into the 3 spots circled on the picture.

    • You can now fasten the wire into the right spot on the trigger piece.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

作成者

6人の作成者と共同で作成されました。

Brian Neuman

メンバー登録日: 01/20/15

893 ポイント

3のガイドは作成済み

チーム

USF Tampa, Team 7-4, Remmell Winter 2015 USF Tampa, Team 7-4, Remmell Winter 2015人のメンバー

USFT-REMMELL-W15S7G4

4 メンバー

3のガイドは作成済み

2 件のコメント

Hi dear, can you say me the order of colours in the USB cable? I think green, white, red, black thin and black thick. Is It correct?

Cas - 返信

Where can I get conductive pads for this?

Ginga - 返信

コメントを追加

統計データ:

過去 24時間: 4

過去 7 日: 13

過去 30 日: 125

今までの合計 8,944