修理を始めるには コミュニティ ストア

Lenovo ThinkPad T400s Heatsink & Fan Replacement

作成者： Matthew Lee (そして 4 人のその他投稿者)
  • コメント: 1
  • お気に入り: 2
  • 完了: 3

難易度

難しい

手順

15

所要時間

1時間

セクション

2

フラグ

0

はじめに

This guide will show you how to replace the heatsink and fan.

  1. Remove the Phillips #0-6mm screw. Lift up the back cover to the RAM cards.

    • Remove the Phillips #0-6mm screw.

    • Lift up the back cover to the RAM cards.

    編集

  2. Pull the lock for the baterry to the left to unlock. While holding the tab in the unlocked position, remove the battery.

    • Pull the lock for the baterry to the left to unlock.

    • While holding the tab in the unlocked position, remove the battery.

    編集

  3. Remove the three Phillips #0-6mm screws on the back panel.

    • Remove the three Phillips #0-6mm screws on the back panel.

    • These screws are marked with a keyboard symbol next to them.

    編集

  4. Turn the computer over and open the lid. Wedge the small metal spudger between the palm rest and the keyboard. Wedge the small metal spudger between the palm rest and the keyboard.

    • Turn the computer over and open the lid.

    • Wedge the small metal spudger between the palm rest and the keyboard.

    編集

  5. Lift up the keyboard, but be careful not to completely remove. Don't lift the keyboard too quickly, there is a connector cable you must disconnect first. Wedge the small plastic opening tool underneath copper band and tilt back.

    • Lift up the keyboard, but be careful not to completely remove.

    • Don't lift the keyboard too quickly, there is a connector cable you must disconnect first.

    • Wedge the small plastic opening tool underneath copper band and tilt back.

    • Remove keyboard to replace.

    編集

  7. Remove the 7 Phillips#0-4mm screws.

    • Remove the 7 Phillips#0-4mm screws.

    編集

  8. Remove the SSD/HDD cover from the lower right corner of the laptop.

    • Remove the SSD/HDD cover from the lower right corner of the laptop.

    編集

  9. Remove the nine Phillips #0-6mm screws on the back panel.

    • Remove the nine Phillips #0-6mm screws on the back panel.

    編集

  10. Pull up on the unlock button while pushing left on the sliding tab. Do not be discouraged if it takes some force.

    • Pull up on the unlock button while pushing left on the sliding tab.

    • Do not be discouraged if it takes some force.

    編集

  11. Use the plastic opening tool to lift the black tab up and remove the palm rest connection. Remove the palm rest by lifting the side nearest to you.

    • Use the plastic opening tool to lift the black tab up and remove the palm rest connection.

    • Remove the palm rest by lifting the side nearest to you.

    編集

  12. Rotate the laptop 90 degrees counter-clockwise. Remove the safety screw on the bottom corner of the laptop by holding the gold cap in place with the tweezers and unscrewing the Phillips screw with the other hand.

    • Rotate the laptop 90 degrees counter-clockwise.

    • Remove the safety screw on the bottom corner of the laptop by holding the gold cap in place with the tweezers and unscrewing the Phillips screw with the other hand.

    編集

  13. Flip the computer over and open the lid. Unscrew the seven Phillips#0-4mm screws. Lift the frame up by the front and pull towards you to remove.

    • Flip the computer over and open the lid. Unscrew the seven Phillips#0-4mm screws.

    • Lift the frame up by the front and pull towards you to remove.

    編集

  14. Remove the two Phillips #0-6.5mm screws from the back side of the laptop to detach the screen. Lift the laptop down facing you, and place the screen down flat behind the laptop.

    • Remove the two Phillips #0-6.5mm screws from the back side of the laptop to detach the screen.

    • Lift the laptop down facing you, and place the screen down flat behind the laptop.

    • The screen will still be connected to the base by wires.

    編集

  15. Remove the eight Phillips #0-3mm screws.

    • Remove the eight Phillips #0-3mm screws.

    • Remove the two Phillips #0-6mm screws.

    • The circuit board will still be attached by the colored wires.

    編集

  16. Tilt up the circuit board to access the heatsink and fan. Disconnect the white connector to remove.

    • Tilt up the circuit board to access the heatsink and fan.

    • Disconnect the white connector to remove.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

作成者

4他の投稿者と一緒に

Matthew Lee

メンバー登録日: 2015年04月14日

247 ポイント

1ガイドが承認済み

バッジ: 10

+7 個以上のバッジ

チーム

Cal Poly, Team 6-18, Maness Spring 2015 Cal Poly, Team 6-18, Maness Spring 2015人のメンバー

CPSU-MANESS-S15S6G18

4 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 1

過去 7 日: 2

過去 30 日: 8

今までの合計 2,838