はじめに

This guide explains how to replace the Case of a LG Neon GT 365 phone

パーツ

パーツは必要ありません。

  1. Remove the back cover of the phone by pushing the rectangular button located on the back top-side of the phone.
    • Remove the back cover of the phone by pushing the rectangular button located on the back top-side of the phone.

  2. Use the appropriate screw driver head and remove the six black screws as shown in the picture. A screw may be covered by the slide spring. Move the slide spring to the other side to access that screw.
    • Use the appropriate screw driver head and remove the six black screws as shown in the picture. A screw may be covered by the slide spring. Move the slide spring to the other side to access that screw.

  3. Use the plastic opening tool to go around the seem and slowly pull off slide spring assembly. Make sure the ribbon connector does not get caught on other parts of the phone.
    • Use the plastic opening tool to go around the seem and slowly pull off slide spring assembly.

    • Make sure the ribbon connector does not get caught on other parts of the phone.

  4. Remove the connector ribbon located  near the bottom of the phone by pulling gently on the ribbon.
    • Remove the connector ribbon located near the bottom of the phone by pulling gently on the ribbon.

  5. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する
  6. Carefully, peel off the two green pieces of tape then the gold tape. Carefully, peel off the two green pieces of tape then the gold tape.
    • Carefully, peel off the two green pieces of tape then the gold tape.

  7. Disconnect the copper colored ribbon. It is fine to leave the copper ribbon ttached to the top of the phone.
    • Disconnect the copper colored ribbon. It is fine to leave the copper ribbon ttached to the top of the phone.

  8. Use the plastic opening tool and go around the silver screen and begin to lift it up.
    • Use the plastic opening tool and go around the silver screen and begin to lift it up.

    • Once the silver screen has been lifted up slightly, slide the bottom half of the green circuit board located below the screen off of the phone. Then continue popping the screen out.

  9. Once the silver screen has been lifted up slightly, slide the bottom half of the green circuit board located below the screen off of the phone.
    • Once the silver screen has been lifted up slightly, slide the bottom half of the green circuit board located below the screen off of the phone.

  10. Disconnect left side of this ribbon. By disconnecting the left side of that ribbon, the phone's screen can be removed from the outer shell.
    • Disconnect left side of this ribbon.

    • By disconnecting the left side of that ribbon, the phone's screen can be removed from the outer shell.

  11. Use the plastic opening tool to remove that speaker out of the groove.
    • Use the plastic opening tool to remove that speaker out of the groove.

    • Use the plastic opening tool to remove the copper colored plate that the speaker and ribbon is attached to out of the phone.

  12. Peel the rubber front keypad out of the case.
    • Peel the rubber front keypad out of the case.

  13. At this point, all of removable phone components has been taken out. With the new case, follow the steps in reverse to reassemble.
    • At this point, all of removable phone components has been taken out. With the new case, follow the steps in reverse to reassemble.

まとめ

To reassemble your device, follow these instructions in reverse order.

kristie

メンバー登録日: 2013年10月23日

538 ポイント

5のガイドは作成済み

チーム

University of Maryland, Team 2-1, Gulbrandsen Fall 2013 University of Maryland, Team 2-1, Gulbrandsen Fall 2013人のメンバー

UMD-GULBRANDSEN-F13S2G1

4 メンバー

10のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 235