はじめに

How to remove the circuit board from an LG CG180 cell phone.

Power down the cell phone by pressing and holding down the red "end call" button.
  • Power down the cell phone by pressing and holding down the red "end call" button.

コメントを追加する

Turn the phone screen-down so you are looking at the back cover.
  • Turn the phone screen-down so you are looking at the back cover.

コメントを追加する

Slide the back cover down using your finger to remove the cover from the phone. Slide the back cover down using your finger to remove the cover from the phone.
  • Slide the back cover down using your finger to remove the cover from the phone.

コメントを追加する

Place your finger at the top of the battery in small gap.
  • Place your finger at the top of the battery in small gap.

コメントを追加する

Press downward while pulling outward to remove the battery.
  • Press downward while pulling outward to remove the battery.

コメントを追加する

Remove all four screws on the back of the phone using a Phillips #00 screwdriver.
  • Remove all four screws on the back of the phone using a Phillips #00 screwdriver.

コメントを追加する

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Insert a plastic opening tool in the seam.
  • Insert a plastic opening tool in the seam.

コメントを追加する

Run the tool along the seam to release all the tabs. Run the tool along the seam to release all the tabs.
  • Run the tool along the seam to release all the tabs.

コメントを追加する

Pull the phone back cover off once all the tabs are released. Pull the phone back cover off once all the tabs are released.
  • Pull the phone back cover off once all the tabs are released.

コメントを追加する

Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.
  • Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.

コメントを追加する

The hardshell case is separated from the rest of the phone.
  • The hardshell case is separated from the rest of the phone.

コメントを追加する

Separate keypad from circuit board by turning it upside down and allowing it to fall off. Separate keypad from circuit board by turning it upside down and allowing it to fall off.
  • Separate keypad from circuit board by turning it upside down and allowing it to fall off.

コメントを追加する

Place the circuit board with the display facing downward.
  • Place the circuit board with the display facing downward.

コメントを追加する

Use thumb to release both white clips at the top of the circuit board.
  • Use thumb to release both white clips at the top of the circuit board.

  • Be careful with the display because it is still attached by electrical tape.

コメントを追加する

Once both clips are released, turn over the circuit board so that the display is facing upward. Carefully lift the display from the left side and open to the right.
  • Once both clips are released, turn over the circuit board so that the display is facing upward.

  • Carefully lift the display from the left side and open to the right.

コメントを追加する

Carefully remove the electrical tape from the display.
  • Carefully remove the electrical tape from the display.

コメントを追加する

The display is disconnected from the circuit board.
  • The display is disconnected from the circuit board.

コメントを追加する

The circuit board is separated from the rest of the phone.
  • The circuit board is separated from the rest of the phone.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Alex Jacobs

メンバー登録日: 2010年01月21日

5 ポイント

8のガイドは作成済み

チーム

Cal Poly, Team 14-42, Regan Winter 2010 Cal Poly, Team 14-42, Regan Winter 2010人のメンバー

CPSU-REGAN-W10S14G42

4 メンバー

10のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 2,730