はじめに

Replace your Kindle's old motherboard with a new one.

Using a spudger or plastic opening tool, gently pry the bezel from the screen. It is easier to start in the corners and work your way around the bezel.
  • Using a spudger or plastic opening tool, gently pry the bezel from the screen. It is easier to start in the corners and work your way around the bezel.

  • Do not insert the spudger too far under the bezel; it could easily damage the screen.

I found it easier to start this step off with one of the Opening Picks found in the iOpener pack.

NathanF - 返信

Remove the eleven 3.0 mm Phillips screws surrounding the midframe.
  • Remove the eleven 3.0 mm Phillips screws surrounding the midframe.

  • At the top of the display, a strip of black tape covers one screw.

On 3G version you will not have the top middle screw.

BJones - 返信

  • Lift the midframe out of the case.

  • If the midframe is stuck, slide it to the left first, and then lift it out.

There are clips in the bottom of the case helping hold the midframe in. Lift the top of the midframe up enough to clear the black back piece and then slide up and out.

BJones - 返信

  • Turn over the midframe to locate the battery.

  • Remove the three Phillips 3.0 mm screws securing the battery to the midframe.

コメントを追加する

  • Gently lift the battery from the bottom, and slide it out of the midframe.

コメントを追加する

  • With the case and battery removed from the midframe, begin removing all cables attached to the motherboard.

  • Place the device so the midframe's backside faces up. Start with the cable on the bottom left corner.

  • Use a spudger to lift up the white locking cable tensioner and slide the flex cable out.

  • Proceed counterclockwise to the next cable and repeat. Small flex cable on the bottom won't need cable tensioner lifted, just carefully pull out.

The second connector is not exactly a "repeat". The lock to be lifted is on the cable side, whereas the first connector's lock is away from the cable.

Yishai Sered - 返信

Does anyone know the part number or for that matter where i can purchase the original LED assembly?

Thanks

naz zan - 返信

  • Remove the white flex cable by gently lifting the yellow plastic connector.

コメントを追加する

  • Remove the yellow anti-static tape from the display ribbon cable connector.

  • Use a spudger to lift up and disconnect the cable tensioner.

コメントを追加する

  • Use a Philips screwdriver to remove the seven 3.0 mm Phillips screws securing the motherboard:

    • Three silver screws with silver washers

    • Two silver screws with no washers

    • One black screw with a golden washer

    • One black screw with a square washer

コメントを追加する

  • Remove the motherboard.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Isabelle Burgess

メンバー登録日: 2013年01月23日

1,040 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 3-33, Amido Winter 2013 Cal Poly, Team 3-33, Amido Winter 2013人のメンバー

CPSU-AMIDO-W13S3G33

4 メンバー

10のガイドは作成済み

Not sure if this is an error, but on the 3G paperwhite, we needed to use a #0 Phillips, not a #2. Great guide otherwise!

Caleb Begly - 返信

Please suggest what type of controller is used and the model and flash memory in the Kindle Paperwhite 1st Generation?

ven 1949, div 0004

Elecrash - 返信

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 14

過去 30 日: 100

今までの合計 15,167