修理を始めるには 修理する権利 ストア

JBL On Stage II Power Button Replacement

作成者： Janessa D Cabrera (そして 4 人のその他投稿者)
  • コメント: 1
  • お気に入り: 0

難易度

簡単

手順

9

所要時間

15 - 20 分

セクション

2

フラグ

0

はじめに

This guide shows you how to replace the spring on the power button.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Turn the device upside down so that the three rubber pads are facing up.

    • Turn the device upside down so that the three rubber pads are facing up.

    編集

  2. Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    編集

  3. Remove the heated rubber pad with a plastic opening tool.

    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

    編集

  5. Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver. Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    編集

  6. Open the device along its seam. Be careful when separating the device because there are wires connecting the two seperate halves. Be careful when separating the device because there are wires connecting the two seperate halves.

    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

    編集

  7. Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    編集

  8. Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device. Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    編集

  9. Pull the plastic button off the post. Pull the plastic button off the post.

    • Pull the plastic button off the post.

    編集

  10. Remove the metal U-clip (compressing the spring) with tweezers.

    • Remove the metal U-clip (compressing the spring) with tweezers.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

4他の投稿者と一緒に

Janessa D Cabrera

メンバー登録日: 2014年01月23日

490 ポイント

4のガイドは作成済み

バッジ: 9

+6 個以上のバッジ

チーム

Cal Poly, Team 9-28, Maness Winter 2014 Cal Poly, Team 9-28, Maness Winter 2014人のメンバー

CPSU-MANESS-W14S9G28

4 メンバー

7のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 5

今までの合計 1,621