メインコンテンツにスキップ

Ivation IVWPDC20Y Flash Bulb Replacement

必要な工具と部品

  1. Ivation IVWPDC20Y Flash Bulb Replacement, Flash Bulb: 手順 1、 1の画像 1
    • With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover

  2. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 2、 1の画像 1
    • Apply a plastic opening tool to each of the corners and gently remove the casing

    • The front casing is held down by adhesive and may require additional work to remove

    • Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal

  3. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 3、 1の画像 1
    • Remove the five silver screws from the inner casing using the PH00 screwdriver bit

  4. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 4、 1の画像 1
    • Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit

    • These screws are very small and easy to strip so apply consistent pressure when removing them

  5. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 5、 1の画像 1
    • Pry off back outer casing using the black spudger or the blue prying tools

  6. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 6、 1の画像 1
    • Carefully remove the screen from the silver casing using a prying tool or the black spudger

    • There is adhesive in the center of the screen, be sure not to bend it when applying pressure

  7. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 7、 1の画像 1
    • Gently push out the pins holding the orange tape down using the pointy end of the spudger

    • Screen and orange tape should slip out as a whole

  8. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 8、 1の画像 1
    • Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver

  9. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 9、 1の画像 1
    • Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver bit

  10. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 10、 1の画像 1
    • Gently lift the corner of the motherboard out

    • Everything should come out as one component free of the casing

  11. Ivation IVWPDC20Y Flash Bulb Replacement: 手順 11、 1の画像 1
    • Remove the soldering on the three wires holding the flash bulb

    • The wires are different colors: red, white, and black

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

3人の作成者と共同で作成されました。

Wendy Jones

メンバー登録日: 02/06/16

225 ポイント

2のガイドは作成済み

チーム

USF Tampa, Team 6-6, Eyestone Spring 2016 USF Tampa, Team 6-6, Eyestone Spring 2016人のメンバー

USFT-EYESTONE-S16S6G6

3 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 242