修理を始めるには コミュニティ ストア

Insignia Flex 8 Speakers Replacement

必要な工具と部品

  1. Insignia Flex 8 Speakers Replacement, Circuit Board: 手順 1、 1の画像 1

    • Turn off the power to your tablet to avoid injury.

    • Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

    • Hold down the power button for five seconds until the tablet powers down.

    編集

  2. Insignia Flex 8 Speakers Replacement: 手順 2、 2の画像 1 Insignia Flex 8 Speakers Replacement: 手順 2、 2の画像 2

    • Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

    • You may need to use a spudger to initially create separation between the screen and the casing.

    • Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

    • Remove the back casing and set aside.

    編集

  3. Insignia Flex 8 Speakers Replacement: 手順 3、 2の画像 1 Insignia Flex 8 Speakers Replacement: 手順 3、 2の画像 2

    • Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

    編集

  4. Insignia Flex 8 Speakers Replacement: 手順 4、 3の画像 1 Insignia Flex 8 Speakers Replacement: 手順 4、 3の画像 2 Insignia Flex 8 Speakers Replacement: 手順 4、 3の画像 3

    • To remove the camera ribbon cable, lift the flap using a spudger.

    • Pull the ribbon directly back to release it.

    編集

  5. Insignia Flex 8 Speakers Replacement: 手順 5、 3の画像 1 Insignia Flex 8 Speakers Replacement: 手順 5、 3の画像 2 Insignia Flex 8 Speakers Replacement: 手順 5、 3の画像 3

    • Remove the second ribbon cable by prying up the black flap using a spudger.

    • Pull the ribbon cable horizontally directly away from the battery.

    編集

  7. Insignia Flex 8 Speakers Replacement: 手順 6、 3の画像 1 Insignia Flex 8 Speakers Replacement: 手順 6、 3の画像 2 Insignia Flex 8 Speakers Replacement: 手順 6、 3の画像 3

    • Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

    • Pull the ribbon horizontally directly away from the battery.

    編集

  8. Insignia Flex 8 Speakers Replacement: 手順 7、 2の画像 1 Insignia Flex 8 Speakers Replacement: 手順 7、 2の画像 2

    • Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

    編集

  9. Insignia Flex 8 Speakers Replacement: 手順 8、 2の画像 1 Insignia Flex 8 Speakers Replacement: 手順 8、 2の画像 2

    • Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

    • Lift up the circuit board.

    編集

  10. Insignia Flex 8 Speakers Replacement: 手順 9、 1の画像 1

    • Unscrew the final two screws that were underneath the circuit board.

    • These screws are near the charging port and USB adapter.

    • These screws are also 3.75mm and can be interchanged with the second set of screws only.

    編集

  11. Insignia Flex 8 Speakers Replacement: 手順 10、 1の画像 1

    • Lift the circuit board and black internal mounting piece away from the screen.

    • Set the circuit board aside.

    • Be careful of the soldered antenna as you separate the pieces.

    • Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

    編集

  12. Insignia Flex 8 Speakers Replacement, Speakers: 手順 11、 2の画像 1 Insignia Flex 8 Speakers Replacement, Speakers: 手順 11、 2の画像 2

    • Looking at the front of the speaker, peel back the rectangular cover to expose the speaker.

    編集

  13. Insignia Flex 8 Speakers Replacement: 手順 12、 1の画像 1

    • Desolder the connections from the circuit board

    • Do not heat up the surrounding components on the circuit board.

    編集

  14. Insignia Flex 8 Speakers Replacement: 手順 13、 1の画像 1

    • Turn the black internal mounting piece over to access the back of the speaker.

    • Use a spudger to lift the cover open.

    • The cover is attached with a plastic solder, be careful not to break the cover.

    編集

  15. Insignia Flex 8 Speakers Replacement: 手順 14、 1の画像 1

    • Pull the speaker out of its housing.

    • Repeat these steps for the other speaker.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

1人の作成者と共同作成されました。

Tyler Tyrrell

メンバー登録日: 03/11/15

890 ポイント

4のガイドは作成済み

バッジ: 17

+14 個以上のバッジ

チーム

Colorado Springs, Team 5-5, Panko Spring 2015 Colorado Springs, Team 5-5, Panko Spring 2015人のメンバー

UCCS-PANKO-S15S5G5

3 メンバー

12のガイドは作成済み

コメント 1 件

coooooooooooooooooooooooooooooooooooooooooooooooooooool

Angel Nicholas - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 438