修理を始めるには コミュニティ ストア

Insignia Flex 10.1 NS-P10W8100 Camera Replacement

はじめに

Although there are no known hazards with removing the camera, be careful not to damage any small components or permanently damage any connectors.

必要な工具と部品

  1. Insignia Flex 10.1 NS-P10W8100 Camera Replacement, Camera: 手順 1、 2の画像 1 Insignia Flex 10.1 NS-P10W8100 Camera Replacement, Camera: 手順 1、 2の画像 2

    • Carefully open the laptop and remove the keyboard by disconnecting it.

    • Place keyboard to the side as you will not need it.

    • Beware of plastic clips on the side of the device.

    編集

  2. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 2、 2の画像 1 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 2、 2の画像 2

    • Lay the screen flat on its surface and use the iFixit opening tool to remove the cover by gently prying the back cover from the screen.

    • Apply the opening tool to each side to help pry the back cover evenly.

    • Apply the opening tool to each side which will help pry the back cover evenly.

    • Do not pry on the bottom side of the device. This is the side across from the camera.

    編集

  4. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 3、 1の画像 1

    • Use your fingers and pry the back cover from the screen. You may need to wiggle the cover a bit to separate the pieces.

    • If the back cover does not come off work your fingers around the corners and slowly pry the cover off using your fingers.

    • Be careful with potential sharp edges and any exposed electrical components.

    編集

  5. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 4、 2の画像 1 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 4、 2の画像 2

    • Carefully remove the yellow tape holding down the camera ribbon connector by pulling it upwards.

    • Remove the black tape holding down the camera ribbon connector which is attached to the motherboard.

    編集

  6. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 5、 2の画像 1 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 5、 2の画像 2

    • Disconnect the zero insertion force (ZIF) connector by using your fingernail to flip the small locking flap.

    • Disconnect the cable by gently pulling it outward.

    編集

  7. Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 6、 3の画像 1 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 6、 3の画像 2 Insignia Flex 10.1 NS-P10W8100 Camera Replacement: 手順 6、 3の画像 3

    • Remove the camera by pulling it upward.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

2人の作成者と共同で作成されました。

Edgar Rodriguez

メンバー登録日: 02/12/19

971 ポイント

5のガイドは作成済み

バッジ: 6

+3 個以上のバッジ

チーム

Western Carolina University, Team S1-G2, Virtue Spring 2019 Western Carolina University, Team S1-G2, Virtue Spring 2019人のメンバー

WCU-VIRTUE-S19S1G2

4 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 2

過去 30 日: 2

今までの合計 189