メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

This guide will teach users how to carefully disassemble the screen of the IBM Thinkpad T60. This will allow users to replace a broken LCD screen or upgrade their current version. Remember to always power down the computer before attempting any installation/removal of any hardware components. Be sure to remove the AC adapter and all cables from the computer. If the computer has been on, wait several minutes before beginning the procedure to ensure all parts have cooled down.

パーツ

パーツは指定されていません。

  1. Turn the computer over to see the small tab on the battery located near the top of the Thinkpad.
    • Turn the computer over to see the small tab on the battery located near the top of the Thinkpad.

    • Use your finger to slide the tab to the right to unlock the battery.

  2. Once the tab is in the unlocked position (far right), pull the battery outwards away from the Thinkpad. The battery is now disconnected.
    • Once the tab is in the unlocked position (far right), pull the battery outwards away from the Thinkpad.

    • The battery is now disconnected.

  3. Open the laptop so that the screen is facing you. Use a plastic opening tool to pry off the eight plastic screw covers around the display. Note that there are screw covers on the sides (two on the left and one on the right).
    • Open the laptop so that the screen is facing you.

    • Use a plastic opening tool to pry off the eight plastic screw covers around the display.

    • Note that there are screw covers on the sides (two on the left and one on the right).

  4. Use a #0 Phillips screwdriver to remove the eight 3.25 mm screws uncapped from the previous step.
    • Use a #0 Phillips screwdriver to remove the eight 3.25 mm screws uncapped from the previous step.

  5. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  6. Carefully pry the plastic border away from the screen using the plastic opening tool. Note that this step requires some force. There are plastic clips that help hold the border in place so do not worry about snapping sounds.
    • Carefully pry the plastic border away from the screen using the plastic opening tool.

    • Note that this step requires some force. There are plastic clips that help hold the border in place so do not worry about snapping sounds.

  7. Use your fingers to pry the screen out of its housing  far enough to gain access to the ribbon cables and small screws holding the screen in place.
    • Use your fingers to pry the screen out of its housing far enough to gain access to the ribbon cables and small screws holding the screen in place.

  8. At the top of the screen, detach the small white clip by pulling it towards you with your finger.
    • At the top of the screen, detach the small white clip by pulling it towards you with your finger.

  9. Using a #0 Phillips screwdriver, remove the 4 mm screw. Using a #0 Phillips screwdriver, remove the 4 mm screw.
    • Using a #0 Phillips screwdriver, remove the 4 mm screw.

  10. Using a #0 Phillips screwdriver, remove the four 3.25 mm screws The other two screws are in the same position on the opposite side of the display.
    • Using a #0 Phillips screwdriver, remove the four 3.25 mm screws

    • The other two screws are in the same position on the opposite side of the display.

  11. The screen should be free to move now. Let the display rest on the keyboard with the screen facing down. Peel the tape off to expose the LCD connection.
    • The screen should be free to move now. Let the display rest on the keyboard with the screen facing down.

    • Peel the tape off to expose the LCD connection.

  12. Turn the inverter over to expose the white clip. Squeeze and pull the wires with your fingers to detach the white clip.
    • Turn the inverter over to expose the white clip.

    • Squeeze and pull the wires with your fingers to detach the white clip.

  13. Disconnect the video cable by pulling the grey flat wire. Now the screen is completely separate from the ThinkPad.
    • Disconnect the video cable by pulling the grey flat wire. Now the screen is completely separate from the ThinkPad.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Cody Kratochvil

メンバー登録日: 2013年01月11日

419 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 7-9, Maness Winter 2013 Cal Poly, Team 7-9, Maness Winter 2013人のメンバー

CPSU-MANESS-W13S7G9

4 メンバー

16のガイドは作成済み

コメント1件

Thanks for the info! ☼

Stck Flw - 返信

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 10

過去 30 日: 44

今までの合計 10,029