メインコンテンツにスキップ

はじめに

Repairability assessment of the Huawei Watch GT, performed July 2019. The model assessed is a black stainless steel FTN-B19.

パーツ

パーツは指定されていません。

  1. Huawei Watch GT Repairability Assessment, Huawei Watch GT Repairability Assessment: 手順 1、 3の画像 1 Huawei Watch GT Repairability Assessment, Huawei Watch GT Repairability Assessment: 手順 1、 3の画像 2 Huawei Watch GT Repairability Assessment, Huawei Watch GT Repairability Assessment: 手順 1、 3の画像 3
    • Exterior reference photos.

  2. Huawei Watch GT Repairability Assessment: 手順 2、 3の画像 1 Huawei Watch GT Repairability Assessment: 手順 2、 3の画像 2 Huawei Watch GT Repairability Assessment: 手順 2、 3の画像 3
    • Two spring bar pins attach the watchbands to the body and allow for easy removal.

    • Reference shots of the front and back of the Huawei Watch GT body.

  3. Huawei Watch GT Repairability Assessment: 手順 3、 3の画像 1 Huawei Watch GT Repairability Assessment: 手順 3、 3の画像 2 Huawei Watch GT Repairability Assessment: 手順 3、 3の画像 3
    • The plastic rear cover of the Huawei Watch GT is secured by 4 Torx T3 screws (3.6 mm length).

    • Applying an opening pick or fingernail to the small notch at the upper edge of the watch is enough to separate the bottom cover.

    • At this point it's possible to open the watch but the display and back cover are still connected by a multi purpose interconnect flex cable.

  4. Huawei Watch GT Repairability Assessment: 手順 4、 3の画像 1 Huawei Watch GT Repairability Assessment: 手順 4、 3の画像 2 Huawei Watch GT Repairability Assessment: 手順 4、 3の画像 3
    • We go by the book and unplug the battery first by removing two Phillips #00 screws (2.9 mm length) and a metal shield.

    • The battery is held in place by mild adhesive and comes out after some gentle heating and prying.

  5. Huawei Watch GT Repairability Assessment: 手順 5、 2の画像 1 Huawei Watch GT Repairability Assessment: 手順 5、 2の画像 2
    • Unplugging the interconnect cable—carrying the vibration motor and the heart rate sensor—requires removing another pair of screws and a small metal shield.

    • Seems like the interconnect flex cable can't be removed from the rear cover—bummer.

  6. Huawei Watch GT Repairability Assessment: 手順 6、 3の画像 1 Huawei Watch GT Repairability Assessment: 手順 6、 3の画像 2 Huawei Watch GT Repairability Assessment: 手順 6、 3の画像 3
    • After removing four more Phillips #00 screws and disconnecting the screen and digitizer connector as well as the side button cable, the motherboard can be removed.

    • The flex cable of the two side buttons is glued to the motherboard with mild adhesive and can be peeled off.

  7. Huawei Watch GT Repairability Assessment: 手順 7、 3の画像 1 Huawei Watch GT Repairability Assessment: 手順 7、 3の画像 2 Huawei Watch GT Repairability Assessment: 手順 7、 3の画像 3
    • Ambiq Micro Apollo3 Blue MCU with ARM Cortex-M4 Processor

    • Winbond 1 Gbit serial NAND flash

    • NXP 80T35 36 04 SSD902, probably NFC controller

    • Broadcom BCM47752 GPS receiver

  8. Huawei Watch GT Repairability Assessment: 手順 8、 1の画像 1
    • The screen and digitizer of the Huawei Watch GT are glued to the display frame with strong adhesive and can not be removed without causing damage to them.

    • So replacing the screen means replacing the complete top part of the watch.

  9. Huawei Watch GT Repairability Assessment: 手順 9、 2の画像 1 Huawei Watch GT Repairability Assessment: 手順 9、 2の画像 2
    • The Huawei Watch GT earns a 5 out of 10 on our repairability scale (10 is the easiest to repair):

    • Watch band replacements are fast and simple.

    • Easy glueless opening procedure.

    • The battery can be removed independently. The removal procedure needs some prying but isn't too bad.

    • The screen and the digitizer can't be removed separately.

    • The sensor assembly including the vibration motor is soldered to the back cover.

ゴール

3 の人々がこのガイドを完成させました。

Dominik Schnabelrauch

メンバー登録日: 2016年11月23日

129,738 ポイント

534のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

141 メンバー

15,073のガイドは作成済み

9 件のコメント

Hi Dominik,thanks for your share!

This article about HUAWEI WATHCH GT teardown is the second I’ve ever seem,and the other is there : 集微拆评 . Combine the two,you’ll found that all the ICs installed on the PCB is clear.

Roc - 返信

do you have any idea where i can buy the spare part for the screen?

I got mine fell, and the screen gradually becoming pitch black. Now it’s completely black, but i think all the other functionalities are okay.

Ridho Akhiro - 返信

The screws in step 3 are not phillips does anyone know what they are?

Mauricio Flores - 返信

Hi Mauricio,

thanks for your comment. Your objection was right and we made a correction in the repairability assessment. The screws securing the rear cover are Torx 3 (T3) screws.

Dominik Schnabelrauch -

コメントを追加

統計データを表示:

過去 24時間: 5

過去 7 日: 55

過去 30 日: 234

今までの合計 13,146