はじめに

Use this guide to replace the rear camera in your Huawei P9 Lite.

ツール

工具は必要ありません。

パーツ

パーツは必要ありません。

  1. Use an opening pick to unclip the rear cover, starting from the bottom corner. Work your way around counterclockwise and carefully pry the plastic tabs open one by one.
    • Use an opening pick to unclip the rear cover, starting from the bottom corner.

    • Work your way around counterclockwise and carefully pry the plastic tabs open one by one.

    What could you use instead of an opening pick??

    Alfredo - 返信

    Like, could a guitar pick wor? Or anything else?

    Alfredo - 返信

    A guitar pick will also do.

    Tobias Isakeit -

    what can still be used besides guitar pick

    Tarshia Thompson - 返信

  2. There is adhesive underneath the back cover that holds it to the battery and the metal plate at the top.
    • There is adhesive underneath the back cover that holds it to the battery and the metal plate at the top.

    • Be careful with the flex cable at the right hand side.

    • Twist the opening pick to lever the back cover away and loosen it from the adhesive.

    Most of the adhesive is around the fingerprint cell and on the battery itself. You can slowly pull the back cover from its side but make sure not to break it. Push the mediator or a longer piece of plastic under the back cover to slowly destroy the adhesive.

    Nicolas Combaret - 返信

  3. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する
  4. When the back cover is freed from the adhesive you can pop it off by hand completely.
    • When the back cover is freed from the adhesive you can pop it off by hand completely.

    Hi! Im so sad! At the begginig of the operation i ve broken the white seal/connector that in one side is connected to the board and the other side is "glued" to the battery. Can someone help me? how can i solve this?? There is no image displayed on the screen. but there is vibration, sound, notifications... can someone help me please???

    Diogo - 返信

  5. Remove the nine Phillips #00 screws that secure the metal shield plate.
    • Remove the nine Phillips #00 screws that secure the metal shield plate.

    • If there are any water indicators on top of the screws remove them to ensure a proper seating for your driver.

  6. Do not remove the shield plate yet, it is attached by a connector and an adhered cable. Use a spudger to disconnect the fingerprint sensor from the motherboard.
    • Do not remove the shield plate yet, it is attached by a connector and an adhered cable.

    • Use a spudger to disconnect the fingerprint sensor from the motherboard.

    • Peel the NFC antenna cable off of the metal plate.

    can we just remove NFC antenna and dont want to install int back?

    Mohd Danial Bin Harun - 返信

    Note there are two plastic tabs at the top of the shield plate. Unlock them with a mediator, the plate will come easily after that.

    Nicolas Combaret - 返信

  7. Release the rear camera connector. Take the camera out of its recess.
    • Release the rear camera connector.

    • Take the camera out of its recess.

まとめ

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Tobias Isakeit

メンバー登録日: 2014年03月31日

43,904 ポイント

104のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

108 メンバー

8,331のガイドは作成済み

コメント1件

So, i ordered some replacement parts for my huawei p9 lite(Main camera, front camera, usb board), Everything i replaced is working, except for the main camera, the new main camera isn’t working, because when i open my camera app it immediately closes, snapchat shows me an error that says: Snapchat was unable to open the camera app. I made sure that the new main camera isn’t working for some reason, because when i put my original camera back in, everything works, including the new front camera). Am i missing something, could it be a hardware problem or a software problem? Please help, i need advices quick. Thanks.

Zygis Bugenis - 返信

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 11

過去 30 日: 59

今までの合計 2,098