はじめに

Use this guide to replace the headphone jack in your Huawei P9 smartphone.

  1. First switch off your phone and remove the SIM card tray. Unscrew the two Pentalobe P2 screws located at the bottom next to the device's USB C port. If the screen is cracked you might want to use some tape to protect your eyes from glass shreds and get a better grip to open the phone.
    • First switch off your phone and remove the SIM card tray.

    • Unscrew the two Pentalobe P2 screws located at the bottom next to the device's USB C port.

    • If the screen is cracked you might want to use some tape to protect your eyes from glass shreds and get a better grip to open the phone.

  2. Use an iSclack or a suction handle to separate the display unit from the rear panel. Don't remove the rear panel completely yet. There is a cable connected to it! It is running from the finger print sensor to the display unit.
    • Use an iSclack or a suction handle to separate the display unit from the rear panel.

    • Don't remove the rear panel completely yet. There is a cable connected to it! It is running from the finger print sensor to the display unit.

    If you cant get suction because of cracks in the screen, use wide tape to create smooth surface.

    Kent Alexander Johansen - 返信

    If your screen is smashed, and nothing else will work (iSclack etc), you can get a thin blade between the casing and the screen assembly and the bottom. The screen assembly can then be pried out. I fought with mine before discovering this. Be careful of the broken glass.

    Rob Collins - 返信

    I struggled to remove screen with suction cups due to damage to the back case. I used a jim to pry from bottom by usb c port, worked well.

    Philip Lloyd - 返信

    Be very carrefull as it can open in one fell swoop !

    Jean-Marc Boisseau - 返信

    On my model, I had 2 Little torx screws beside the USB port. If so, the screen won’t come out with them on.

    Lola Gillet - 返信

    Interesting, sure those were 6-starred (Torx) and not 5-starred (Pentalobe) like mentioned in step 1?

    Tobias Isakeit -

  3. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する
  4. Disconnect the finger print sensor using a spudger. Disconnect the finger print sensor using a spudger.
    • Disconnect the finger print sensor using a spudger.

  5. Remove the water indicator on top of the screw. Undo the two Phillips #00 screws. Remove metal bracket (mind the adhesive underneath).
    • Remove the water indicator on top of the screw.

    • Undo the two Phillips #00 screws.

    • Remove metal bracket (mind the adhesive underneath).

  6. Disconnect the flex cable and remove the headphone jack. The old headphone jack is equipped with a rubber seal, which holds the jack down to the phone. Take it off and put it on the new headphone jack.
    • Disconnect the flex cable and remove the headphone jack.

    • The old headphone jack is equipped with a rubber seal, which holds the jack down to the phone. Take it off and put it on the new headphone jack.

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Tobias Isakeit

メンバー登録日: 2014年03月31日

43,536 ポイント

102のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

108 メンバー

8,298のガイドは作成済み

コメント1件

questo procedimento funziona anche con il modello p9 plus? grazie per l’attenzione

abcde181 - 返信

コメントを追加する

統計データを表示:

過去 24時間: 8

過去 7 日: 20

過去 30 日: 131

今までの合計 3,597