メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

Use this guide to replace the loudspeaker in your Huawei Mate 8.

  1. Switch off your phone and remove the SIM card tray. Switch off your phone and remove the SIM card tray.
    • Switch off your phone and remove the SIM card tray.

  2. Remove the Torx T2 screws from the bottom of the phone
    • Remove the Torx T2 screws from the bottom of the phone

  3. Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel. Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel.
    • Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel.

  4. Use an opening pick to fully separate the clips, releasing the phone. Do not fully remove the rear case. The fingerprint sensor cable is still connected to the back cover. Open the phone like a book from the SIM tray side.
    • Use an opening pick to fully separate the clips, releasing the phone.

    • Do not fully remove the rear case. The fingerprint sensor cable is still connected to the back cover.

    • Open the phone like a book from the SIM tray side.

    • Use a spudger, to disconnect the fingerprint sensor cable.

  5. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  6. Remove the liquid indicator sticker. Remove the Phillips #00 screw that holds down the metal shield. The metal shield is tightly held in place. If you try to remove it without holding it down on one side, it'll break easily.
    • Remove the liquid indicator sticker.

    • Remove the Phillips #00 screw that holds down the metal shield.

    • The metal shield is tightly held in place. If you try to remove it without holding it down on one side, it'll break easily.

    • Use a spudger to remove the metal shield.

  7. Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables. Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables. Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables.
    • Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables.

  8. Remove the Phillips #00 screw that holds down the interconnect cable bracket.
    • Remove the Phillips #00 screw that holds down the interconnect cable bracket.

  9. Lift the coaxial connector off of its socket to allow access to the daughterboard interconnect cable bracket. Remove the bracket.
    • Lift the coaxial connector off of its socket to allow access to the daughterboard interconnect cable bracket.

    • Remove the bracket.

  10. Use a spudger to disconnect the interconnect cable.
    • Use a spudger to disconnect the interconnect cable.

    • Remove the interconnect cable.

  11. Remove the two Phillips #00 screws. Use the flat end a spudger to disconnect the loudspeaker flex connector. Use the pointy end of a spudger to pry out the daughterboard.
    • Remove the two Phillips #00 screws.

    • Use the flat end a spudger to disconnect the loudspeaker flex connector.

    • Use the pointy end of a spudger to pry out the daughterboard.

    • Remove the daughterboard.

  12. Remove the two Phillips #00 screws. Use the tip of a spudger on the left side of the loudspeaker to pry it out. Remove the loudspeaker.
    • Remove the two Phillips #00 screws.

    • Use the tip of a spudger on the left side of the loudspeaker to pry it out.

    • Remove the loudspeaker.

終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Theo Mat

メンバー登録日: 2017年11月12日

11,370 ポイント

14のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 2

過去 7 日: 4

過去 30 日: 16

今までの合計 552