メインコンテンツにスキップ

How to Clean and Sharpen your Wahl Hair Clippers

必要な工具と部品

  1. How to Clean and Sharpen your Wahl Hair Clippers, How to Clean and Sharpen your Wahl Hair Clippers: 手順 1、 1の画像 1
    • Take your Philips head screwdriver and loosen the set screws by turning them left. This will allow you to separate the blades from your clipper.

  2. How to Clean and Sharpen your Wahl Hair Clippers: 手順 2、 1の画像 1
    • Take a fine hair brush and sweep it across the clipper base. This will remove any hair debris.

  3. How to Clean and Sharpen your Wahl Hair Clippers: 手順 3、 1の画像 1
    • Fully immerse and soak your blade in 90% isopropyl alcohol to remove any rust that might be present. The blade should soak a minimum of 5 minutes.

  4. How to Clean and Sharpen your Wahl Hair Clippers: 手順 4、 1の画像 1
    • Take a clean lint free towel and dry the blade. While drying rub the blade in all directions applying light pressure and this will remove residue and polish the blade.

  5. How to Clean and Sharpen your Wahl Hair Clippers: 手順 5、 1の画像 1
    • Run your blade left and right in a horizontal direction across a Whetstone honing stone. First on the coarse side to sharpen the blade then on the finishing side to smooth out the blade.

  6. How to Clean and Sharpen your Wahl Hair Clippers: 手順 6、 1の画像 1
    • Rinse the honing stone under water and rub the stone back and forth the same direction you used to sharpen your blade. This will clean your stone and remove any debris.

  7. How to Clean and Sharpen your Wahl Hair Clippers: 手順 7、 1の画像 1
    • Place your blades back into position and insert your set screws into the proper holes. Take your Philips screwdriver and turn the screws to the right until you feel them completely tighten. Be careful to line up your blades correctly.

  8. How to Clean and Sharpen your Wahl Hair Clippers: 手順 8、 1の画像 1
    • Apply oil to the base of your blades before first use. Blades should be oiled after every 3 or 4 uses.

  9. How to Clean and Sharpen your Wahl Hair Clippers: 手順 9、 1の画像 1
    • Your clippers are ready for use. Plug them in to let them run for a few moments before your first use.

終わりに

To reassemble your device, follow these instructions in reverse order.

17 の人々がこのガイドを完成させました。

作成者

1人の作成者と共同作成されました。

Joseph Makar

メンバー登録日: 02/07/19

689 ポイント

1ガイドが承認済み

チーム

Pasco Hernando, Team S6-G84, Prince Spring 2019 Pasco Hernando, Team S6-G84, Prince Spring 2019人のメンバー

PHSC-PRINCE-S19S6G84

1 メンバー

5のガイドは作成済み

8 件のコメント

What kind of oil? wd40 ?

zoobee22 - 返信

No. WD40 is not a lube and won't last. WD = Water Displacer.

Use mineral oil from your drug store.

Joe -

Much more easily said than done. I am extremely mechanically orientated and have tried three times to sharpen them. They are almost useless (Wahl animal Pro Series) after only two cuts.

Barry Jameson - 返信

Barry, read my comment to the step 5 - you’ll find how to do it correct.

vladintool -

My shaver after popping the head off to clean stop cutting.what steps can I take to fix this problem?

mdearl54@yahoo.com - 返信

コメントを追加

統計データ:

過去 24時間: 66

過去 7 日: 561

過去 30 日: 2,516

今までの合計 109,068