メインコンテンツにスキップ

Hover-1 H1 Gyroscope Sensor Assemblies Replacement

必要な工具と部品

  1. Hover-1 H1 Gyroscope Sensor Assemblies Replacement, Bottom Shell: 手順 1、 1の画像 1
    • Remove the ten 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

    • Remove the twelve 9mm sheet metal screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

  2. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 2、 1の画像 1
    • Puncture the two black stickers by using the tip of a screwdriver.

    • Remove the two 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

  3. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 3、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 3、 2の画像 2
    • Lift each side of the bottom shell by pulling up.

    • When lifting the shell, take care to not tear any cables from their connectors.

  4. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 4、 1の画像 1
    • Unplug the battery by pulling gently on both sides of the orange connector.

  5. Hover-1 H1 Gyroscope Sensor Assemblies Replacement, Gyroscope Sensor Assemblies: 手順 5、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement, Gyroscope Sensor Assemblies: 手順 5、 2の画像 2
    • On the battery side of the hoverboard, remove the red, black, and purple sleeved cable from the sensor assembly by squeezing the tab and pulling up.

  6. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 6、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 6、 2の画像 2
    • Remove the red, blue, and green cable from the cable extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

  7. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 7、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 7、 2の画像 2
    • Remove the four 7mm screws by using a Phillips #2 screwdriver to rotate the screws counterclockwise.

  8. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 8、 1の画像 1
    • Remove the sensor assembly on the battery side of the hoverboard by gently lifting and pulling away from the hoverboard.

  9. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 9、 3の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 9、 3の画像 2 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 9、 3の画像 3
    • Remove the hot glue holding in the connectors with a utility knife.

    • Remove the white cable from the sensor assembly by squeezing the connector and pulling the connector up.

    • Be careful not to touch any parts of the circuit boards with the knife.

  10. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 10、 1の画像 1
    • Remove the red, blue, and green cable from the extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

  11. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 11、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 11、 2の画像 2
    • Remove the red and black sleeved connector from the sensor assembly by squeezing the tab and pulling up.

  12. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 12、 2の画像 1 Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 12、 2の画像 2
    • Remove the four 7mm screws by using a Phillips #2 screwdriver to rotate the screws counterclockwise.

  13. Hover-1 H1 Gyroscope Sensor Assemblies Replacement: 手順 13、 1の画像 1
    • Remove the sensor assembly on the motherboard side of the hoverboard by gently lifting and pulling away from the hoverboard.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

作成者

4人の作成者と共同で作成されました。

Aaron Teh

メンバー登録日: 10/08/18

421 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team S17-G6, White Fall 2018 Cal Poly, Team S17-G6, White Fall 2018人のメンバー

CPSU-WHITE-F18S17G6

4 メンバー

7のガイドは作成済み

コメント 1 件

where can I get the replacement parts?

Rob Sayles - 返信

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 18

過去 30 日: 87

今までの合計 4,736