メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

Use this guide to remove or replace the front panel on the HTC Vive controller. Be careful not to tear the ribbon cables or any of the connectors they correspond to while removing the front panel.

パーツ

パーツは指定されていません。

  1. Turn over the Vive controller so that the bottom saucer is facing up. Use the T5 Torx screwdriver to remove three black 21mm screws from the bottom saucer. Use the T5 Torx screwdriver to remove three black 21mm screws from the bottom saucer.
    • Turn over the Vive controller so that the bottom saucer is facing up.

    • Use the T5 Torx screwdriver to remove three black 21mm screws from the bottom saucer.

  2. Use the nylon spudger to separate the top and bottom saucer covers all around the edges. Remove only the top saucer cover by pulling up with your hand.
    • Use the nylon spudger to separate the top and bottom saucer covers all around the edges.

    • Remove only the top saucer cover by pulling up with your hand.

  3. Use the Phillips 00 screwdriver to remove the three silver 12.8mm screws from the exposed upper sensor panel. Use the Phillips 00 screwdriver to remove the three silver 12.8mm screws from the exposed upper sensor panel.
    • Use the Phillips 00 screwdriver to remove the three silver 12.8mm screws from the exposed upper sensor panel.

  4. Carefully pull away the bottom saucer cover with your hand. To aid in removing the saucer cover, squeeze the base of the controller with your other hand, as shown in the second image of this step. Squeezing will make the clips easier to release and help prevent them from breaking. To aid in removing the saucer cover, squeeze the base of the controller with your other hand, as shown in the second image of this step. Squeezing will make the clips easier to release and help prevent them from breaking.
    • Carefully pull away the bottom saucer cover with your hand.

    • To aid in removing the saucer cover, squeeze the base of the controller with your other hand, as shown in the second image of this step. Squeezing will make the clips easier to release and help prevent them from breaking.

  5. 今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

    今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る
  6. Use the T5 Torx screwdriver to remove the two black 5.2mm screws on the back gray panel. Use the T5 Torx screwdriver to remove the two black 5.2mm screws on the back gray panel.
    • Use the T5 Torx screwdriver to remove the two black 5.2mm screws on the back gray panel.

  7. Turn over the Vive controller so that the exposed bottom saucer panel is facing up.
    • Turn over the Vive controller so that the exposed bottom saucer panel is facing up.

    • Use the T5 Torx screwdriver to remove the three black 5.2mm screws.

  8. Use the nylon spudger to separate the front panel gently by running the spudger around the edges of the handle. Only separate the front panel around the edges. Do not try to completely remove the panel yet.
    • Use the nylon spudger to separate the front panel gently by running the spudger around the edges of the handle.

    • Only separate the front panel around the edges. Do not try to completely remove the panel yet.

    • Gently lift the right side of the panel to the left.

  9. Disconnect the upper ribbon cable gently by pulling the ribbon up and  away from the motherboard with two fingers.
    • Disconnect the upper ribbon cable gently by pulling the ribbon up and away from the motherboard with two fingers.

    • Do not try to disconnect the ribbon cables from the front panel.

  10. Disconnect the middle ribbon cable gently by pulling the ribbon cable up and away from the motherboard with two fingers. Do not try to disconnect the ribbon cables from the front panel.
    • Disconnect the middle ribbon cable gently by pulling the ribbon cable up and away from the motherboard with two fingers.

    • Do not try to disconnect the ribbon cables from the front panel.

  11. Use the nylon spudger to lift  the white tab by 90 degrees. Disconnect the bottom ribbon cable gently by pulling the ribbon cable down with two fingers. Disconnect the bottom ribbon cable gently by pulling the ribbon cable down with two fingers.
    • Use the nylon spudger to lift the white tab by 90 degrees.

    • Disconnect the bottom ribbon cable gently by pulling the ribbon cable down with two fingers.

終わりに

To reassemble your device, follow these instructions in reverse order.

10 の人々がこのガイドを完成させました。

Ryan Grewohl

メンバー登録日: 2017年10月02日

565 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team S15-G5, Livingston Fall 2017 Cal Poly, Team S15-G5, Livingston Fall 2017人のメンバー

CPSU-LIVINGSTON-F17S15G5

4 メンバー

8のガイドは作成済み

コメント1件

Hi, I recently broke my HTC vive contrôler and the ribbon cables of the touchpad is now disconnect from the front panel. Is it dead or I can plug it on is place ?

Chausse - 返信

コメントを追加

統計データを表示:

過去 24時間: 5

過去 7 日: 20

過去 30 日: 78

今までの合計 5,034