パーツ

パーツは必要ありません。

Flip the phone over to have the rear cover facing up.
  • Flip the phone over to have the rear cover facing up.

    • The camera lens should be towards the top of the phone.

コメントを追加する

Slide the cover up, towards the top of phone, to unlock the battery cover. Lift the cover off phone and remove it.
  • Slide the cover up, towards the top of phone, to unlock the battery cover.

  • Lift the cover off phone and remove it.

コメントを追加する

Use your finger to push the top of the battery downwards and lift the battery out of the phone. Use your finger to push the top of the battery downwards and lift the battery out of the phone. Use your finger to push the top of the battery downwards and lift the battery out of the phone.
  • Use your finger to push the top of the battery downwards and lift the battery out of the phone.

コメントを追加する

Remove the six Torx #5 screws that are securing the rear frame. Remove the six Torx #5 screws that are securing the rear frame. Remove the six Torx #5 screws that are securing the rear frame.
  • Remove the six Torx #5 screws that are securing the rear frame.

コメントを追加する

Pry the frame open, releasing the eight plastic tabs around the edge of the frame, using the plastic opening tool. A plastic card can be used instead of the plastic opening tool. A plastic card can be used instead of the plastic opening tool.
  • Pry the frame open, releasing the eight plastic tabs around the edge of the frame, using the plastic opening tool.

    • A plastic card can be used instead of the plastic opening tool.

コメントを追加する

Remove the single Phillips #0 screw that is securing the motherboard to the front case of the phone. Remove the single Phillips #0 screw that is securing the motherboard to the front case of the phone.
  • Remove the single Phillips #0 screw that is securing the motherboard to the front case of the phone.

コメントを追加する

Pry the motherboard away from the front of the plastic case using a plastic opening tool. Be careful not to break the ribbon cable when prying away the motherboard.
  • Pry the motherboard away from the front of the plastic case using a plastic opening tool.

    • Be careful not to break the ribbon cable when prying away the motherboard.

コメントを追加する

Remove the plastic cover from the LCD display and the motherboard. The Motherboard and the LCD are still attached together. The Motherboard and the LCD are still attached together.
  • Remove the plastic cover from the LCD display and the motherboard.

    • The Motherboard and the LCD are still attached together.

コメントを追加する

Remove the gray tape securing the ribbon cable. Remove the gray tape securing the ribbon cable.
  • Remove the gray tape securing the ribbon cable.

コメントを追加する

Remove the yellow tape securing the connector lock.
  • Remove the yellow tape securing the connector lock.

コメントを追加する

Carefully lift the black lock to release the ribbon cable, using the plastic opening tool. Carefully lift the black lock to release the ribbon cable, using the plastic opening tool.
  • Carefully lift the black lock to release the ribbon cable, using the plastic opening tool.

コメントを追加する

Pull the ribbon cable upwards, disconnecting it from the Motherboard.
  • Pull the ribbon cable upwards, disconnecting it from the Motherboard.

コメントを追加する

Lift the Motherboard away from the LCD display.
  • Lift the Motherboard away from the LCD display.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Marco Jokada

メンバー登録日: 2011年04月28日

247 ポイント

6のガイドは作成済み

チーム

CSU Los Angeles, Team 1-2, Nelson Spring 2011 CSU Los Angeles, Team 1-2, Nelson Spring 2011人のメンバー

CSULA-NELSON-S11S1G2

5 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 2,008