メインコンテンツにスキップ

HTC Desire 610 Charging Port Replacement

必要な工具と部品

  1. HTC Desire 610 Charging Port Replacement, Black Plastic Circuit Cover: 手順 1、 3の画像 1 HTC Desire 610 Charging Port Replacement, Black Plastic Circuit Cover: 手順 1、 3の画像 2 HTC Desire 610 Charging Port Replacement, Black Plastic Circuit Cover: 手順 1、 3の画像 3
    • Using a plastic opening tool, take off the back cover of the phone.

  2. HTC Desire 610 Charging Port Replacement: 手順 2、 1の画像 1
    • Remove the four black 4mm torx screws using the Torx T5 bit.

  3. HTC Desire 610 Charging Port Replacement: 手順 3、 1の画像 1
    • Remove the four silver 5mm torx head screws using the Torx T5 screwdriver.

  4. HTC Desire 610 Charging Port Replacement: 手順 4、 1の画像 1
    • Remove the two 2.5mm phillips head screws using the Phillips 000 screwdriver.

  5. HTC Desire 610 Charging Port Replacement: 手順 5、 1の画像 1
    • Remove the black plastic circuit cover using a plastic opening tool.

  6. HTC Desire 610 Charging Port Replacement, Charging Port: 手順 6、 1の画像 1
    • Remove the 4mm black Torx screw using a Torx T5 screwdriver.

  7. HTC Desire 610 Charging Port Replacement: 手順 7、 1の画像 1
    • Using a pair of tweezers, disconnect the antenna wire.

  8. HTC Desire 610 Charging Port Replacement: 手順 8、 3の画像 1 HTC Desire 610 Charging Port Replacement: 手順 8、 3の画像 2 HTC Desire 610 Charging Port Replacement: 手順 8、 3の画像 3
    • Peel back the gray adhesive strip using the precision tweezers.

  9. HTC Desire 610 Charging Port Replacement: 手順 9、 1の画像 1
    • Pull up on the white strip so it sits 90 degrees using a pair of precision tweezers.

  10. HTC Desire 610 Charging Port Replacement: 手順 10、 3の画像 1 HTC Desire 610 Charging Port Replacement: 手順 10、 3の画像 2 HTC Desire 610 Charging Port Replacement: 手順 10、 3の画像 3
    • Pry up the circuit board and pull it out using a pair of precision tweezers.

  11. HTC Desire 610 Charging Port Replacement: 手順 11、 3の画像 1 HTC Desire 610 Charging Port Replacement: 手順 11、 3の画像 2 HTC Desire 610 Charging Port Replacement: 手順 11、 3の画像 3
    • Remove the loud speaker using a pair of precision tweezers.

    • The loud speaker is attached with adhesive and may require more force than expected to remove.

    • The prongs on the speaker should be sticking up towards the top of the phone when you put the speaker on the new circuit board.

終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

4人の作成者と共同で作成されました。

Kaycee Hammond

メンバー登録日: 02/11/17

273 ポイント

2のガイドは作成済み

チーム

IUPUI, Team S1-G1, Wilson Spring 2017 IUPUI, Team S1-G1, Wilson Spring 2017人のメンバー

IUPUI-WILSON-S17S1G1

4 メンバー

6のガイドは作成済み

コメント 1 件

Super duper 5

Nizamcdk - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 5

今までの合計 1,217