メインコンテンツにスキップ

はじめに

The purpose of this guide is to instruct the reader on how to replace the joypad of their HP iPAQ H2200 device.

パーツ

パーツは指定されていません。

  1. Press and slide the battery cover tab to remove battery cover.
    • Press and slide the battery cover tab to remove battery cover.

  2. Pull on the black tab to lift the battery out of the battery compartment. Pull on the black tab to lift the battery out of the battery compartment.
    • Pull on the black tab to lift the battery out of the battery compartment.

  3. Remove the stylus by sliding it out of the slot.
    • Remove the stylus by sliding it out of the slot.

  4. Remove the CF card by sliding it out of the slot at the top of the device.
    • Remove the CF card by sliding it out of the slot at the top of the device.

  5. Press down and push the black side strips toward the top of the device to remove them.
    • Press down and push the black side strips toward the top of the device to remove them.

  6. PCラップトップ用バッテリー

    iFixitの品質保証付きトップPCブランド用バッテリー

    ショップを見る

    PCラップトップ用バッテリー

    iFixitの品質保証付きトップPCブランド用バッテリー

    ショップを見る
  7. Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device.
    • Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

  8. Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side). Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).
    • Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

  9. Open the LCD connector, where the orange strip attaches to the main board.
    • Open the LCD connector, where the orange strip attaches to the main board.

  10. Carefully remove the orange LCD strip from the connector.
    • Carefully remove the orange LCD strip from the connector.

  11. Unscrew the 2 screws located at each top corner of the main board.
    • Unscrew the 2 screws located at each top corner of the main board.

  12. Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.
    • Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

  13. Press on the four joypad tabs on the back, and push it through and out the front.
    • Press on the four joypad tabs on the back, and push it through and out the front.

  14. Push the new joypad through the hole; the tabs will lock it into place.
    • Push the new joypad through the hole; the tabs will lock it into place.

まとめ

To reassemble your device, follow these instructions in reverse order.

Tyler Andrews

メンバー登録日: 2010年01月13日

191 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 4-12, Forte Winter 2010 Cal Poly, Team 4-12, Forte Winter 2010人のメンバー

CPSU-FORTE-W10S4G12

3 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 2

今までの合計 2,842