メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

HP Compaq dx2000MT RAM Replacement

作成者： Logan Pace (そして 3 人のその他投稿者)
  • コメント: 1
  • お気に入り: 12
  • 完了: 1

難易度

普通

手順

15

所要時間

10 - 15 分

セクション

3

フラグ

1

Markup Mishap

間違いの指摘

このガイドは最適な校正が必要です。校正の注釈を付けたり訂正することにご協力ください。

はじめに

This guide will show you how to remove the RAM on your HP Compaq dx2000MT.

ツール

これらのツールを購入する

パーツ

これらのパーツを購入する

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.

    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

    翻訳

  2. Remove the 2 Phillips #2 screws that secure the case door to the device. Remove the 2 Phillips #2 screws that secure the case door to the device.

    • Remove the 2 Phillips #2 screws that secure the case door to the device.

    翻訳

  3. Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

    翻訳

  4. Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

    翻訳

  5. Remove the IDE data and power cables from the hard drive Remove the IDE data and power cables from the hard drive Remove the IDE data and power cables from the hard drive

    • Remove the IDE data and power cables from the hard drive

    翻訳

  6. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する

  7. Remove the front bezel by pulling upwards and out from below the lowest air vent. Remove the front bezel by pulling upwards and out from below the lowest air vent. Remove the front bezel by pulling upwards and out from below the lowest air vent.

    • Remove the front bezel by pulling upwards and out from below the lowest air vent.

    翻訳

  8. Remove the external drive faceplate by removing the 2 Torx T15 Screws Remove the external drive faceplate by removing the 2 Torx T15 Screws Remove the external drive faceplate by removing the 2 Torx T15 Screws

    • Remove the external drive faceplate by removing the 2 Torx T15 Screws

    翻訳

  9. Remove the following screws: Front Torx T15.

    • Remove the following screws:

    • Front Torx T15.

    • Torx T15 mounting the hard drive cage to the optical drive bay.

    翻訳

  10. Fully remove the hard drive cage by sliding it towards the back of the device and pulling down. Fully remove the hard drive cage by sliding it towards the back of the device and pulling down. Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.

    • Fully remove the hard drive cage by sliding it towards the back of the device and pulling down.

    翻訳

  11. Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place

    • Remove 2 Torx T15 screws holding this side of the hard drive in place

    翻訳

  12. Proceed to the other side of the hard drive cage Remove 2 Torx T15 screws holding this side of the hard drive in place Remove 2 Torx T15 screws holding this side of the hard drive in place

    • Proceed to the other side of the hard drive cage

    • Remove 2 Torx T15 screws holding this side of the hard drive in place

    翻訳

  13. Remove the hard drive from the hard drive cage by pulling it outward from the cage Remove the hard drive from the hard drive cage by pulling it outward from the cage

    • Remove the hard drive from the hard drive cage by pulling it outward from the cage

    翻訳

  14. Release the lower portion of the RAM by pushing down on the bottom tab. Release the lower portion of the RAM by pushing down on the bottom tab.

    • Release the lower portion of the RAM by pushing down on the bottom tab.

    翻訳

  15. Release the upper portion of the RAM by pushing down on the upper tab. Release the upper portion of the RAM by pushing down on the upper tab.

    • Release the upper portion of the RAM by pushing down on the upper tab.

    翻訳

  16. Remove the RAM by pulling it out towards the side of the device Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity in your fingers could short it. If you can, only touch the top and bottom of the RAM. If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise the RAM may not fit or your computer may not start up.

    • Remove the RAM by pulling it out towards the side of the device

    • Be careful about touching the top (right) and bottom (left)sides of the RAM! The static electricity in your fingers could short it. If you can, only touch the top and bottom of the RAM.

    • If replacing RAM, make sure it is the right type, speed, and size for your computer. Otherwise the RAM may not fit or your computer may not start up.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

3他の投稿者と一緒に

Logan Pace

メンバー登録日: 2011年10月12日

2,020 ポイント

9のガイドは作成済み

バッジ: 14

+11 個以上のバッジ

チーム

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S17G16

4 メンバー

17のガイドは作成済み

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 11

今までの合計 3,910