メインコンテンツにスキップ

はじめに

This guide will demonstrate how to clean or replace the strummer (strum bar) for a Guitar Hero: World Tour Controller.

The strummer can often become sluggish or stuck from wear and tear over time. This can often be solved by simply cleaning or lubricating the strum bar, or by replacing it entirely if damaged.

Two AA batteries will need to be removed as shown in the guide.

  1. Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 手順 1、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 手順 1、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement, Strummer: 手順 1、 3の画像 3
    • Remove the battery cover.

    • Remove the two AA batteries.

  2. Guitar Hero World Tour Guitar Strummer Replacement: 手順 2、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement: 手順 2、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement: 手順 2、 3の画像 3
    • Move the switch from "Locked" to the "Unlocked" position.

    • Remove the neck from the body of the guitar.

    • This will likely take two hands.

  3. Guitar Hero World Tour Guitar Strummer Replacement: 手順 3、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement: 手順 3、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement: 手順 3、 3の画像 3
    • Ensure the face-plate lock is in the "Unlocked" position.

    • Pry the face plate off of the body by gently prying with an opening tool near the marked locations. The face plate should not be difficult to remove.

    • You can pry the face plate away with your fingers, or with any plastic/wooden tool.

    • Avoid using metal tools to pry the plastic face plate away, as it can lead to marring the plastic and ruining the finish.

  4. Guitar Hero World Tour Guitar Strummer Replacement: 手順 4、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement: 手順 4、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement: 手順 4、 3の画像 3
    • Remove the eleven Torx T10 screws.

    • Remove the four Phillips #0 screws.

    • There is an additional Torx T10 screw located behind the "Warranty Void" sticker.

    • Separate the two halves of the guitar body.

  5. Guitar Hero World Tour Guitar Strummer Replacement: 手順 5、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement: 手順 5、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement: 手順 5、 3の画像 3
    • Disconnect the ribbon cable connecting the strummer circuit board to the main control board.

    • Remove the eight Phillips #0 screws holding the strummer circuit board to the body.

    • Ensure that the switches have a solid clicking action.

    • Debris can often block the switches from actuating.

  6. Guitar Hero World Tour Guitar Strummer Replacement: 手順 6、 3の画像 1 Guitar Hero World Tour Guitar Strummer Replacement: 手順 6、 3の画像 2 Guitar Hero World Tour Guitar Strummer Replacement: 手順 6、 3の画像 3
    • Remove four Phillips #0 screws holding the strum bar assembly.

    • Remove the strum bar assembly from the body. Ensure that both springs are present and in good condition.

    • Check the joint between the strum bar and its mounting brackets. Ensure there are no foreign objects jamming the hole. Ensure the joint is well lubricated.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Daniel Koelzer

メンバー登録日: 2021年09月30日

157 ポイント

1ガイドが承認済み

チーム

University of North Texas, Team 2-8, Raign Fall 2021 University of North Texas, Team 2-8, Raign Fall 2021人のメンバー

UNT-RAIGN-F21S2G8

2 メンバー

2のガイドは作成済み

コメント1件

Great guide! Helped me find some loose screws that fixed the strumming when tightened.

Only note is that my controller uses Torx T6 screws instead of Phillips #0 screws. From info online, it looks like these controllers can have either type.

Nicholas Stecyna - 返信

コメントを追加

統計データを表示:

過去 24時間: 8

過去 7 日: 66

過去 30 日: 325

今までの合計 1,315