修理を始めるには コミュニティ ストア

Graco Secure Coverage Vibrator Replacement on Parent Unit

はじめに

Use this guide to replace the vibrator on your Graco Secure Coverage Digital Baby Monitor for parent unit.

The vibrator replacement includes the vibrator and battery replacement.

必要な工具と部品

  1. Graco Secure Coverage Vibrator Replacement on Parent Unit, Parent Unit Battery: 手順 1、 3の画像 1 Graco Secure Coverage Vibrator Replacement on Parent Unit, Parent Unit Battery: 手順 1、 3の画像 2 Graco Secure Coverage Vibrator Replacement on Parent Unit, Parent Unit Battery: 手順 1、 3の画像 3

    • Using plastic opening tool, pry and remove the battery lid.

    編集

  2. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 2、 1の画像 1

    • Remove the battery by holding the device with one hand and pulling the battery out with other hand carefully.

    • Make sure that you disconnect the battery's wire before you remove the battery.

    編集

  3. Graco Secure Coverage Vibrator Replacement on Parent Unit, Parent Unit Vibrator: 手順 3、 2の画像 1 Graco Secure Coverage Vibrator Replacement on Parent Unit, Parent Unit Vibrator: 手順 3、 2の画像 2

    • There are two screws on the rare case of the device. For the one shown in blue marker requires either an extended screwdriver or putting on a little pressure on a regular screwdriver.

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • If you cannot remove the screw with low pressure, do not use high pressure to remove it. It may cause a damage on the device case. Use an extended screwdriver instead.

    編集

  5. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 4、 2の画像 1 Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 4、 2の画像 2

    • Using opening plastic tool, pry the two grey cases from both sides of the device.

    • Take your time and apply constant force to avoid breaking or damaging any other plastic parts.

    • While pry off the grey cases, hold the device with your other hand to remove the cases.

    編集

  6. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 5、 1の画像 1

    • Pry the edges of the device to separate the front case away from the rare case.

    • While prying the edges, hold the device with one hand to pull out each case a part.

    • Make sure you use a constant force, and the pushbuttons are pried off completely.

    編集

  7. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 6、 2の画像 1 Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 6、 2の画像 2

    • Remove the 7mm Phillips #1 screw from the mother board.

    • Place the screw in a secure place.

    編集

  8. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 7、 1の画像 1

    • Pick up the motherboard carefully.

    • Using plastic opening tool, pry and remove the vibrator part.

    編集

  9. Graco Secure Coverage Vibrator Replacement on Parent Unit: 手順 8、 1の画像 1

    • Solder off vibrator from the motherboard.

    • There are many pins attached to the motherboard, make sure you solder off the proper pins that attached to the vibrator wires.

    • Replace the vibrator.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Ahmed Elshaer

メンバー登録日: 09/09/15

201 ポイント

2のガイドは作成済み

バッジ: 6

+3 個以上のバッジ

チーム

USF Tampa, Team 6-5, Remmell Fall 2015 USF Tampa, Team 6-5, Remmell Fall 2015人のメンバー

USFT-REMMELL-F15S6G5

4 メンバー

8のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 2

今までの合計 505