メインコンテンツにスキップ
  1. この手順は未翻訳です。 翻訳を手伝う。

    Remove the following screws that secure the midframe to the back:
    • Remove the following screws that secure the midframe to the back:

    • Seven black 4 mm T5 screws

    • Two silver 3 mm T5 screws

  2. この手順は未翻訳です。 翻訳を手伝う。

    The midframe is held tightly in place by plastic clips which push into the edge of the back case.
    • The midframe is held tightly in place by plastic clips which push into the edge of the back case.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Find the small notch in the bottom left corner of the frame and insert an opening pick. Slide the opening pick along the bottom edge of the phone towards the bottom right corner and leave it there. Slide the opening pick along the bottom edge of the phone towards the bottom right corner and leave it there.
    • Find the small notch in the bottom left corner of the frame and insert an opening pick.

    • Slide the opening pick along the bottom edge of the phone towards the bottom right corner and leave it there.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Insert a separate opening pick into the right edge of the phone, near the bottom. Slowly push the pick upwards along the seam until the first clip pops free. Due to the tight tolerances, this may be difficult, requiring a substantial amount of force. If you are having trouble, try inserting and sliding a playing card.
    • Insert a separate opening pick into the right edge of the phone, near the bottom.

    • Slowly push the pick upwards along the seam until the first clip pops free.

    • Due to the tight tolerances, this may be difficult, requiring a substantial amount of force. If you are having trouble, try inserting and sliding a playing card.

    • Once you've released the clip, leave the opening pick in place to prevent the midframe from resealing.

  5. この手順は未翻訳です。 翻訳を手伝う。

    Insert an opening pick into the right edge of the phone and slide it upwards towards the top right clip. You do not need to insert the pick more than 2 mm into the edge. If you insert the pick all the way in, you may risk damaging flex cables.
    • Insert an opening pick into the right edge of the phone and slide it upwards towards the top right clip.

    • You do not need to insert the pick more than 2 mm into the edge. If you insert the pick all the way in, you may risk damaging flex cables.

    • Slowly slide the pick past the clip to disengage it from the frame.

    • At this point, the right edge of the midframe should be free from the case. If it isn't, slide an opening clip up and down along the right edge.

  6. この手順は未翻訳です。 翻訳を手伝う。

    Grasp the right edge of the midframe by the corners and slowly hinge the edge up. When the left edge feels loose, stop hinging and lift the midframe upwards. Remove the midframe.
    • Grasp the right edge of the midframe by the corners and slowly hinge the edge up.

    • When the left edge feels loose, stop hinging and lift the midframe upwards.

    • Remove the midframe.

    • To reinstall the midframe, align it to the case, then squeeze around the perimeter until all the clips snap back into position. When properly done, the midframe should lie flat.

ゴール

Arthur Shi

メンバー登録日: 2018年01月03日

177,544 ポイント

429のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

138 メンバー

15,634のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 81