メインコンテンツにスキップ
  1. GoPro Hero 3 Silver Expansion Port Replacement, Battery: 手順 1、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement, Battery: 手順 1、 2の画像 2
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. GoPro Hero 3 Silver Expansion Port Replacement: 手順 2、 1の画像 1
    • Pull the battery out using the tab.

  3. GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: 手順 3、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: 手順 3、 2の画像 2
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. GoPro Hero 3 Silver Expansion Port Replacement: 手順 4、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 4、 2の画像 2
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. GoPro Hero 3 Silver Expansion Port Replacement: 手順 5、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 5、 2の画像 2
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  6. GoPro Hero 3 Silver Expansion Port Replacement: 手順 6、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 6、 2の画像 2
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  7. GoPro Hero 3 Silver Expansion Port Replacement: 手順 7、 3の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 7、 3の画像 2 GoPro Hero 3 Silver Expansion Port Replacement: 手順 7、 3の画像 3
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

  8. GoPro Hero 3 Silver Expansion Port Replacement: 手順 8、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 8、 2の画像 2
    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There is a little silver bracket (in the yellow circle) that is held down by the Phillips #00 screw so be careful not to lose it.

  9. GoPro Hero 3 Silver Expansion Port Replacement: 手順 9、 2の画像 1 GoPro Hero 3 Silver Expansion Port Replacement: 手順 9、 2の画像 2
    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

    • Remove the media adapter from the motherboard.

終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Brian Alvarez

メンバー登録日: 2015年04月02日

1,415 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 24-7, Lancaster Spring 2015 Cal Poly, Team 24-7, Lancaster Spring 2015人のメンバー

CPSU-LANCASTER-S15S24G7

3 メンバー

21のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 12

今までの合計 1,545