修理を始めるには コミュニティ ストア

General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement

はじめに

Use this guide to replace the upper feed roller bearing in a General Pipe Cleaners Drain Cleaner PMEBO 2016.

必要な工具と部品

  1. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement, Upper Feed Roller Bearing: 手順 1、 1の画像 1

    • Before you begin, make sure the drain cleaner is disconnected from power.

    • Use your hand to unscrew and remove the feed pressure knob.

    編集

  2. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 2、 1の画像 1

    • Use a 1/4 inch socket wrench to remove the three bolts securing the feed roller holder plate.

    編集

  3. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 3、 1の画像 1

    • Remove the feed roller holder plate.

    編集

  5. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 4、 1の画像 1

    • Use a 3/16 inch hex wrench to remove the top swing pin.

    編集

  6. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 5、 3の画像 1 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 5、 3の画像 2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 5、 3の画像 3

    • Use pliers to lift out and remove the pressure spring plate.

    • Lift out and remove the pressure spring.

    編集

  7. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 6、 2の画像 1 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 6、 2の画像 2

    • Use pliers to lift the top carrier straight up and out of the feed body.

    • During reassembly, make sure that the carrier is oriented so that its threaded hole lines up with the swing pin hole in the feed body.

    • During reassembly, clean the carrier and apply new grease before inserting it into the feed body.

    編集

  8. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 7、 1の画像 1

    • Use a 3/16 inch hex wrench to remove the feed roller shaft.

    • It may be necessary to insert a thin screwdriver or hex wrench into the top end of the carrier to help hold the carrier while you loosen the feed roller shaft.

    編集

  9. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: 手順 8、 1の画像 1

    • Remove the upper feed roller assembly, including the fiber disks on either side of it.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

Adam O'Camb

メンバー登録日: 04/11/15

197,115 ポイント

416のガイドは作成済み

バッジ: 39

+36 個以上のバッジ

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 6

過去 30 日: 18

今までの合計 833