はじめに

Use this repair guide to replace the screen if it has been damaged.

Remove the back battery cover by pinching down on the tab and pulling outward.
  • Remove the back battery cover by pinching down on the tab and pulling outward.

コメントを追加する

Remove the six back panel screws using a Y1 screw driver.
  • Remove the six back panel screws using a Y1 screw driver.

コメントを追加する

  • Remove bottom back panel screw with a Phillips #1 screw driver.

コメントを追加する

  • Remove the back panel by pulling away with one hand and the front secured in the other hand.

  • Beware of right and triggers, the right and left panels, and the power switch falling off as the back panel is removed.

コメントを追加する

  • Remove left and right triggers by lifting and pulling them away from the system.

  • Do the same for side panels.

  • For finicky or jammed triggers only. Adjust and correct triggers and reassemble. Most jammed triggers are caused by buttons misplaced or jammed in its enclosure.

コメントを追加する

  • Remove the gray On/Off Switch by pulling up and away from the unit. Replace with another switch if necessary.

コメントを追加する

  • Remove the three screws on the circuit board with a Phillips #1 screw driver.

    • The last screw on the right is not included on some Game Boy Advance systems.

コメントを追加する

  • Pull circuit board away from the front panel by pulling up at the bottom of the circuit board, keeping the top ribbon still connected.

  • Beware not to damage the top ribbon by pulling up gently.

コメントを追加する

  • Remove the rubber button pads from their pockets.

  • Remove the plastic buttons and the D-pad from beneath the rubber pads with tweezers or by hand.

コメントを追加する

  • Use a spudger/tweezers/fingernail to unlatch the LCD ribbon port by pulling the grey tabs on the sides upwards (towards the top edge of the PCB).

  • Once the LCD ribbon port has been unlatched, the LCD ribbon should very easily slide out and can be removed with zero force using fingers or tweezers.

Guide does not indicate that the ribbon cable port should be UNLATCHED before attempting to remove the ribbon cable, I strongly suggest revising this as someone unfamiliar with these style of ports may assume that the ribbon cable is a compression fit and just needs to be "pulled" free of the port.

This is a terrible idea that will potentially result in tearing the ribbon! Please consider revising guide to add a step to indicate the proper method/detail for unlatching the LCD ribbon port! Thanks :)

Ben Steel - 返信

  • Use the spudger to lift the screen from the front panel. Place the spudger in the space directly left of the D-pad.

  • The screen and the front panel is connected by a black tape that could rip if not removed carefully.

コメントを追加する

  • Use the tweezers to remove the black tape if needed.

コメントを追加する

ゴール

9 の人々がこのガイドを完成させました。

Adam

メンバー登録日: 2010年01月20日

634 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 16-29, Maness Winter 2010 Cal Poly, Team 16-29, Maness Winter 2010人のメンバー

CPSU-MANESS-W10S16G29

5 メンバー

26のガイドは作成済み

Doesn't say where you can get new screen !!!!??

andrew Davies - 返信

Doesn't say where to get screen from !!!??

andrew Davies - 返信

Do this with the Game Boy Advance SP please!

Santi12008 - 返信

It does not say where you can get a new screen

criscaanca - 返信

コメントを追加する

統計データを表示:

過去 24時間: 5

過去 7 日: 48

過去 30 日: 194

今までの合計 13,420