メインコンテンツにスキップ

はじめに

Before attempting repairs, please take note of certain risks of receiving shock from the camera's flash capacitor. Also make sure to ground yourself before operating on the camera's motherboard or you might discharge static to crucial components.

  1. First, push in the lens and remove the two AA batteries. First, push in the lens and remove the two AA batteries. First, push in the lens and remove the two AA batteries.
    • First, push in the lens and remove the two AA batteries.

  2. Open the rear compartment and remove the film cartridge. Open the rear compartment and remove the film cartridge.
    • Open the rear compartment and remove the film cartridge.

  3. Remove screws from bottom of camera with a small #00 Phillips Screwdriver. Then remove screws around the camera. Additionally, there are two screws in the battery compartment which also need to be removed. Remove screws from bottom of camera with a small #00 Phillips Screwdriver. Then remove screws around the camera. Additionally, there are two screws in the battery compartment which also need to be removed. Remove screws from bottom of camera with a small #00 Phillips Screwdriver. Then remove screws around the camera. Additionally, there are two screws in the battery compartment which also need to be removed.
    • Remove screws from bottom of camera with a small #00 Phillips Screwdriver. Then remove screws around the camera. Additionally, there are two screws in the battery compartment which also need to be removed.

  4. PCラップトップ用バッテリー

    iFixitの品質保証付きトップPCブランド用バッテリー

    ショップを見る

    PCラップトップ用バッテリー

    iFixitの品質保証付きトップPCブランド用バッテリー

    ショップを見る
  5. Once all screws are removed, gently pry open the front casing with your hands or plastic opening tools carefully. Do note that there will be a spring that attaches the front casing and the main circuit board, so refrain from allowing excess tension on the spring. Once all screws are removed, gently pry open the front casing with your hands or plastic opening tools carefully. Do note that there will be a spring that attaches the front casing and the main circuit board, so refrain from allowing excess tension on the spring. Once all screws are removed, gently pry open the front casing with your hands or plastic opening tools carefully. Do note that there will be a spring that attaches the front casing and the main circuit board, so refrain from allowing excess tension on the spring.
    • Once all screws are removed, gently pry open the front casing with your hands or plastic opening tools carefully. Do note that there will be a spring that attaches the front casing and the main circuit board, so refrain from allowing excess tension on the spring.

  6. Locate the photo-flash capacitor, then find all the connecting wires to the motherboard and battery compartment. Take notes to which exact wires they are to limit mistakes. Locate the photo-flash capacitor, then find all the connecting wires to the motherboard and battery compartment. Take notes to which exact wires they are to limit mistakes. Locate the photo-flash capacitor, then find all the connecting wires to the motherboard and battery compartment. Take notes to which exact wires they are to limit mistakes.
    • Locate the photo-flash capacitor, then find all the connecting wires to the motherboard and battery compartment. Take notes to which exact wires they are to limit mistakes.

  7. Carefully pry out the capacitor with a spudger or plastic opening tools. Carefully pry out the capacitor with a spudger or plastic opening tools. Carefully pry out the capacitor with a spudger or plastic opening tools.
    • Carefully pry out the capacitor with a spudger or plastic opening tools.

  8. With a solder kit, heat the connecting solder points to open the connection, thus removing the connecting wires. There are many ways to do this, depending on the available tools on hand. With a solder kit, heat the connecting solder points to open the connection, thus removing the connecting wires. There are many ways to do this, depending on the available tools on hand. With a solder kit, heat the connecting solder points to open the connection, thus removing the connecting wires. There are many ways to do this, depending on the available tools on hand.
    • With a solder kit, heat the connecting solder points to open the connection, thus removing the connecting wires. There are many ways to do this, depending on the available tools on hand.

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Boyang Wu

メンバー登録日: 2012年10月02日

705 ポイント

5のガイドは作成済み

チーム

USF Tampa, Team 4-1, Meier Fall 2015 USF Tampa, Team 4-1, Meier Fall 2015人のメンバー

USFT-MEIER-F15S4G1

4 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 9

過去 7 日: 24

過去 30 日: 202

今までの合計 10,672