メインコンテンツにスキップ

はじめに

This repair guide will show you how to replace the battery on a Fossil Q Marshal Gen 2 smartwatch. Be careful not to damage the wiring or the metal connectors on your smartwatch.

  1. Squeeze retaining pins together to release chain from watch body. This can be done by hand or with tweezers.
    • Squeeze retaining pins together to release chain from watch body. This can be done by hand or with tweezers.

    • Remove chain from opposing side of watch body.

  2. Use tweezers to grip the notches on the back cover, then unscrew the back cover (counter-clockwise) from the watch housing.
    • Use tweezers to grip the notches on the back cover, then unscrew the back cover (counter-clockwise) from the watch housing.

    • There is an actual tool made to remove this back cover, using the right tool may save you from scratching the back of watch with tweezers. The backcover tool can be purchased online, a local jeweler may also be willing to remove it for you.

  3. Utilize tweezers or a spudger or your fingers to pull the black wire connector from the motherboard. Utilize a spudger to pull the orange connector off of the motherboard.
    • Utilize tweezers or a spudger or your fingers to pull the black wire connector from the motherboard.

    • Utilize a spudger to pull the orange connector off of the motherboard.

  4. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now
  5. Utilize tweezers to pull the white battery connector from the motherboard.
    • Utilize tweezers to pull the white battery connector from the motherboard.

  6. The internal electronics can now be pulled out of the watch as one unit leaving the screen remaining in the watch housing. Taking the flat end of the spudger, pry it up. Taking the flat end of the spudger, pry it up.
    • The internal electronics can now be pulled out of the watch as one unit leaving the screen remaining in the watch housing.

    • Taking the flat end of the spudger, pry it up.

  7. The battery is secured to the back of the motherboard utilizing a sticky pad. Gently separate the battery from the board while making sure not to put too much stress on the board. This is best done at the location shown.
    • The battery is secured to the back of the motherboard utilizing a sticky pad. Gently separate the battery from the board while making sure not to put too much stress on the board. This is best done at the location shown.

  8. Remove battery from plastic housing. Slip wires through large slot in plastic housing to completely remove.
    • Remove battery from plastic housing.

    • Slip wires through large slot in plastic housing to completely remove.

まとめ

To reassemble your device, follow these instructions in reverse order.

5 の人々がこのガイドを完成させました。

Clay Walker

メンバー登録日: 2017年11月07日

278 ポイント

1ガイドが承認済み

チーム

IUPUI, Team S2-G5, Harley Fall 2017 IUPUI, Team S2-G5, Harley Fall 2017人のメンバー

IUPUI-HARLEY-F17S2G5

3 メンバー

4のガイドは作成済み

I have read your awesome guide. This is really helpful.

https://powerbank-online.com/reviews/bat...

Ellen Sam - 返信

thank you, i did it. But now what. i have no idea where to buy the spare part. hahaha. Help Me :(

Rafael “Satriabhi” Atheya - 返信

I have the exact same battery I need to replace. easy to take out but where do I get the replacement battery??

dustykeith17 - 返信

Help! I can’t find a replacement battery.

Pedro Pimentel - 返信

コメントを追加する

統計データを表示:

過去 24時間: 17

過去 7 日: 109

過去 30 日: 518

今までの合計 5,866