メインコンテンツにスキップ

Flip Video LCD Screen

必要な工具と部品

  1. Flip Video LCD Screen, Outer Shell: 手順 1、 2の画像 1 Flip Video LCD Screen, Outer Shell: 手順 1、 2の画像 2
    • Turn off the device and take the batteries out.

    • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

  2. Flip Video LCD Screen: 手順 2、 1の画像 1
    • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

  3. Flip Video LCD Screen: 手順 3、 2の画像 1 Flip Video LCD Screen: 手順 3、 2の画像 2
    • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

  4. Flip Video LCD Screen: 手順 4、 1の画像 1
    • Open battery door. This can be done by gently depressing and sliding the battery down downward.

  5. Flip Video LCD Screen: 手順 5、 1の画像 1
    • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

  6. Flip Video LCD Screen, Circuit Board: 手順 6、 1の画像 1
    • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

  7. Flip Video LCD Screen: 手順 7、 1の画像 1
    • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

  8. Flip Video LCD Screen: 手順 8、 1の画像 1
    • Disconnect the USB port cable from the back side of the circuit board.

  9. Flip Video LCD Screen: 手順 9、 1の画像 1
    • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

  10. Flip Video LCD Screen, LCD Screen: 手順 10、 1の画像 1
    • With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

  11. Flip Video LCD Screen: 手順 11、 1の画像 1
    • Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

  12. Flip Video LCD Screen: 手順 12、 1の画像 1
    • Gently pull out ribbon cable.

    • If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.

    • The LCD screen is now removed and can be replaced.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

5人の作成者と共同で作成されました。

Elizabeth

メンバー登録日: 04/15/10

100 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 26-21, Regan Spring 2010 Cal Poly, Team 26-21, Regan Spring 2010人のメンバー

CPSU-REGAN-S10S26G21

4 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 7

今までの合計 5,227