はじめに

You may need to replace your bridge because of broken or rusted pieces, or may just want a new look or style.

Start by loosening the strings. This is done by turning the tuning knob until the string has lost tension. Repeat this for all six strings on the guitar. Repeat this for all six strings on the guitar.
  • Start by loosening the strings. This is done by turning the tuning knob until the string has lost tension.

  • Repeat this for all six strings on the guitar.

コメントを追加する

Be mindful of the string ends. They may be sharp and could puncture your skin. It may be necessary to use pliers to remove string ends from the tuning peg.
  • Be mindful of the string ends. They may be sharp and could puncture your skin.

  • It may be necessary to use pliers to remove string ends from the tuning peg.

コメントを追加する

After removing the strings from the tuning pegs, slide the strings through the bridge and out of the back of the guitar. If the twists in the string ends are in the way, use wire cutters to snip them off. This will allow the heavier strings to pass through the bridge easier. If the twists in the string ends are in the way, use wire cutters to snip them off. This will allow the heavier strings to pass through the bridge easier.
  • After removing the strings from the tuning pegs, slide the strings through the bridge and out of the back of the guitar.

  • If the twists in the string ends are in the way, use wire cutters to snip them off. This will allow the heavier strings to pass through the bridge easier.

コメントを追加する

On the back of the guitar, remove the plate covering the spring cavity. In the spring cavity, reduce the tension on the bridge springs by first loosening the retainer screws a bit. On the back of the guitar, remove the plate covering the spring cavity. In the spring cavity, reduce the tension on the bridge springs by first loosening the retainer screws a bit.
  • On the back of the guitar, remove the plate covering the spring cavity. In the spring cavity, reduce the tension on the bridge springs by first loosening the retainer screws a bit.

コメントを追加する

To remove the springs from the bridge, grip the end with pliers and pull up. It is safe to use the body of the guitar for leverage. It is safe to use the body of the guitar for leverage.
  • To remove the springs from the bridge, grip the end with pliers and pull up.

    • It is safe to use the body of the guitar for leverage.

コメントを追加する

Be aware that the ground wire for the electronics of the guitar is routed through the body and soldered to the spring retainer. Be aware that the ground wire for the electronics of the guitar is routed through the body and soldered to the spring retainer. Be aware that the ground wire for the electronics of the guitar is routed through the body and soldered to the spring retainer.
  • Be aware that the ground wire for the electronics of the guitar is routed through the body and soldered to the spring retainer.

コメントを追加する

Remove the screws from the front of the bridge. It may be helpful to only loosen the outer screws as you remove the inner screws, in order to prevent damage to the guitar. It may be helpful to only loosen the outer screws as you remove the inner screws, in order to prevent damage to the guitar.
  • Remove the screws from the front of the bridge.

    • It may be helpful to only loosen the outer screws as you remove the inner screws, in order to prevent damage to the guitar.

コメントを追加する

With all six screws removed, lift up on the bridge to remove it from the body.
  • With all six screws removed, lift up on the bridge to remove it from the body.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Christopher Hartigan

メンバー登録日: 2014年09月10日

89 ポイント

5のガイドは作成済み

チーム

Pasco Hernando, Team 5-3, Prince Fall 2014 Pasco Hernando, Team 5-3, Prince Fall 2014人のメンバー

PHSC-PRINCE-F14S5G3

9 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 2

過去 30 日: 12

今までの合計 813