修理を始めるには コミュニティ ストア

EDCO Disk Grinder 50200-HD Belt Replacement

はじめに

Follow this guide to replace the belt on a EDCO Disk Grinder model 50200-HD.

This repair requires two people.

必要な工具と部品

  1. EDCO Disk Grinder 50200-HD Belt Replacement, Safety precautions: 手順 1、 1の画像 1

    • Before you begin, ensure the device is powered down and cool to the touch.

    • Ensure the machine is unplugged.

    • Turn the power switch counterclockwise into the OFF position.

    編集

  2. EDCO Disk Grinder 50200-HD Belt Replacement, Remove the weighted hood: 手順 2、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement, Remove the weighted hood: 手順 2、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement, Remove the weighted hood: 手順 2、 3の画像 3

    • Use a 9/16 inch socket to remove the two bolts securing the weighted hood.

    • During reassembly, ensure the bolts are reinstalled with the washers and lock washers in the correct order.

    編集

  3. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 3、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 3、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 3、 3の画像 3

    • Remove the weighted hood.

    • The weighted hood weighs 37 pounds. Wear gloves and handle with caution.

    編集

  4. EDCO Disk Grinder 50200-HD Belt Replacement, Remove the belt: 手順 4、 2の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement, Remove the belt: 手順 4、 2の画像 2

    • Use a 9/16 inch socket to loosen the bolts securing the motor mount.

    • Do not completely remove the bolts.

    編集

  6. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 5、 2の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 5、 2の画像 2

    • Slide the motor towards the front of the machine as far as it will go to loosen the belt tension.

    • Use a 9/16 inch socket to tighten the four bolts back down to lock the motor in a position where there's the least belt tension.

    • During reassembly, have one person slide the motor mount towards the rear of the machine to tension the belt while the other person tightens the bolts.

    編集

  7. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 6、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 6、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 6、 3の画像 3

    • Tilt the front of the machine up and rest the handlebars on the ground.

    • Have someone hold down the handlebars to prevent tipping while working on the belt.

    編集

  8. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 7、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 7、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 7、 3の画像 3

    • Pinch a flathead screwdriver between the belt and sheave.

    • Rotate the sheave and pivot the belt up and away from its groove.

    編集

  9. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 8、 2の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 8、 2の画像 2

    • Continue to rotate the sheave with once hand while holding the flathead screwdriver with the other to fully dislodge the belt from the groove.

    編集

  10. EDCO Disk Grinder 50200-HD Belt Replacement: 手順 9、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 9、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement: 手順 9、 3の画像 3

    • Remove the belt from the motor pulley, then fully remove it from the machine.

    • Reassembly tip: loop the belt around the motor pulley before placing it on the sheave.

    編集

  11. EDCO Disk Grinder 50200-HD Belt Replacement, Reassembly tip: 手順 10、 3の画像 1 EDCO Disk Grinder 50200-HD Belt Replacement, Reassembly tip: 手順 10、 3の画像 2 EDCO Disk Grinder 50200-HD Belt Replacement, Reassembly tip: 手順 10、 3の画像 3

    • Reassembly tip: place the belt over the rim and rotate the sheave to guide the belt into the groove.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

Sam Omiotek

メンバー登録日: 02/25/19

73,232 ポイント

288のガイドは作成済み

バッジ: 35

+32 個以上のバッジ

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 7

今までの合計 343