はじめに

This guide will show how to replace damaged casing on the Dremel MultiPro 395.

パーツ

パーツは必要ありません。

  1. Remove the blue caps located on either side of the MultiPro, using a 3 mm flathead screwdriver. Remove the blue caps located on either side of the MultiPro, using a 3 mm flathead screwdriver.
    • Remove the blue caps located on either side of the MultiPro, using a 3 mm flathead screwdriver.

  2. Carefully remove the carbon brushes attached at the end of the springs by gently pulling on the springs using your hands. Carefully remove the carbon brushes attached at the end of the springs by gently pulling on the springs using your hands.
    • Carefully remove the carbon brushes attached at the end of the springs by gently pulling on the springs using your hands.

  3. Pull one side of the hanger up and then pull away from the Multipro until the other side can be pulled out. Pull one side of the hanger up and then pull away from the Multipro until the other side can be pulled out.
    • Pull one side of the hanger up and then pull away from the Multipro until the other side can be pulled out.

  4. Free shipping on all orders over $100.00 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する

    Ever fixed something? That’s Genius.

    Share your repair story with #ImAGenius

    We Are All Geniuses

    Share your repair story with #ImAGenius

  5. Remove the 4 screws located on the bottom of the Multipro with a T15 screwdriver. Remove the 4 screws located on the bottom of the Multipro with a T15 screwdriver. Remove the 4 screws located on the bottom of the Multipro with a T15 screwdriver.
    • Remove the 4 screws located on the bottom of the Multipro with a T15 screwdriver.

  6. Hold down the collet lock, remove the chuck cap from the top of the Multipro by screwing counterclockwise. Hold down the collet lock, remove the chuck cap from the top of the Multipro by screwing counterclockwise. Hold down the collet lock, remove the chuck cap from the top of the Multipro by screwing counterclockwise.
    • Hold down the collet lock, remove the chuck cap from the top of the Multipro by screwing counterclockwise.

  7. Remove the black housing cap from the Multipro located directly below the chuck cap. Remove the black housing cap from the Multipro located directly below the chuck cap. Remove the black housing cap from the Multipro located directly below the chuck cap.
    • Remove the black housing cap from the Multipro located directly below the chuck cap.

  8. Pull the bottom side of the casing up to remove it. Pull the bottom side of the casing up to remove it. Pull the bottom side of the casing up to remove it.
    • Pull the bottom side of the casing up to remove it.

  9. Gently lift the motor shaft out of the Multipro. Gently lift the motor shaft out of the Multipro. Gently lift the motor shaft out of the Multipro.
    • Gently lift the motor shaft out of the Multipro.

  10. Pull the lock pin and its casing out of the other side of the Multipro case. Pull the lock pin and its casing out of the other side of the Multipro case. Pull the lock pin and its casing out of the other side of the Multipro case.
    • Pull the lock pin and its casing out of the other side of the Multipro case.

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Matthew Satton

メンバー登録日: 2014年09月17日

353 ポイント

2のガイドは作成済み

チーム

University of Kentucky Louisville, Team 1-5, Mathis Fall 2014 University of Kentucky Louisville, Team 1-5, Mathis Fall 2014人のメンバー

LOUISVILLE-MATHIS-F14S1G5

5 メンバー

4のガイドは作成済み

コメント1件

A link to parts is always nice,

bari - 返信

統計データを表示:

過去 24時間: 1

過去 7 日: 8

過去 30 日: 29

今までの合計 1,140