修理を始めるには コミュニティ ストア

Disassembling General Electric Telephone 2-9710A Base Shell

はじめに

This guide gives step-by-step instructions for removing the outer shell of the base to assess the logic board within the phone. After completing this guide, you will have access to the logic board and all other interior parts of the telephone.

必要な工具と部品

  1. Disassembling General Electric Telephone 2-9710A Base Shell, Phone Cord: 手順 1、 2の画像 1 Disassembling General Electric Telephone 2-9710A Base Shell, Phone Cord: 手順 1、 2の画像 2

    • Unplug the device before proceeding.

    • Using a plastic opening tool, remove the phone cord from the phone jack at the base of the headset.

    • To release the cable, gently press down on the top plastic tab of the connector.

    編集

  2. Disassembling General Electric Telephone 2-9710A Base Shell: 手順 2、 3の画像 1 Disassembling General Electric Telephone 2-9710A Base Shell: 手順 2、 3の画像 2 Disassembling General Electric Telephone 2-9710A Base Shell: 手順 2、 3の画像 3

    • Remove the 7.5 mm screw.

    • Remove the screw cap.

    • Pull up the phone cord to remove it from the base.

    編集

  3. Disassembling General Electric Telephone 2-9710A Base Shell, 9V Base Battery: 手順 3、 2の画像 1 Disassembling General Electric Telephone 2-9710A Base Shell, 9V Base Battery: 手順 3、 2の画像 2

    • Remove the battery compartment door (located on the bottom of the radio) by applying thumb pressure to the area indicated on the battery door.

    • Slide the door off of the battery compartment.

    • Remove the battery from the phone.

    編集

  4. Disassembling General Electric Telephone 2-9710A Base Shell, Remove Volume Dial: 手順 4、 2の画像 1 Disassembling General Electric Telephone 2-9710A Base Shell, Remove Volume Dial: 手順 4、 2の画像 2

    • Ensure the phone is unplugged from the phone jack and the electrical source.

    • Locate the volume dial on the right side of the telephone.

    • Remove the volume dial by gently grasping it and pulling it away from the base.

    編集

  5. Disassembling General Electric Telephone 2-9710A Base Shell, Remove Screws on the Back: 手順 5、 1の画像 1

    • Remove the three 12 mm screws with a Phillips #1 screwdriver.

    • Remove the three 18 mm screws with a Phillips #1 screwdriver.

    編集

  6. Disassembling General Electric Telephone 2-9710A Base Shell, Pry the Back Off: 手順 6、 2の画像 1 Disassembling General Electric Telephone 2-9710A Base Shell, Pry the Back Off: 手順 6、 2の画像 2

    • Pry off the base shell using a plastic opener tool.

    • Set the shell aside.

    • You now have access to the internal components of the General Electric Telephone 2-9710A.

    編集
終わりに

Reassemble your devise by following these instructions in reverse order.

作成者

10人の作成者と共同で作成されました。

Alles Rebel

メンバー登録日: 09/20/12

72 ポイント

3のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

Cal Poly, Team 16-59, Forte Fall 2012 Cal Poly, Team 16-59, Forte Fall 2012人のメンバー

CPSU-FORTE-F12S16G59

4 メンバー

17のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 779