はじめに

Use this guide to repair a broken battery door. The battery door on this model tends to break off due to a weak plastic hinge.

パーツ

パーツは必要ありません。

Remove the two 3mm (1/8") black screws from the side cover using a #00 Phillips screwdriver.
  • Remove the two 3mm (1/8") black screws from the side cover using a #00 Phillips screwdriver.

コメントを追加する

On the bottom, remove the 6mm (13/64") screw with the #00 Phillips Screwdriver.
  • On the bottom, remove the 6mm (13/64") screw with the #00 Phillips Screwdriver.

  • Pry up the panel; starting from the front/bottom corner, as indicated.

    • There's a concealed lip, under the opposite edge.

コメントを追加する

Remove three medium length screws from the bottom of the camera
  • Remove three medium length screws from the bottom of the camera

コメントを追加する

Remove the two medium length screws on the front panel of the camera above the lens mount.
  • Remove the two medium length screws on the front panel of the camera above the lens mount.

  • Once you done, you may use the Spudger to panel from non-grip side.

  • If you start on the grip side, it will be more challenging to loosen the panel.

コメントを追加する

Remove the two 4.5mm (.18in) long black screws from the camera grip using a #00 Phillips screwdriver.
  • Remove the two 4.5mm (.18in) long black screws from the camera grip using a #00 Phillips screwdriver.

コメントを追加する

Use your fingertip to pry off the external shutter port cover.
  • Use your fingertip to pry off the external shutter port cover.

コメントを追加する

Remove the two 5mm (.20in) long silver screws securing the grip to the camera using a #00 Phillips screwdriver.
  • Remove the two 5mm (.20in) long silver screws securing the grip to the camera using a #00 Phillips screwdriver.

コメントを追加する

Use the spudger tool to carefully pry the grip from the rest of the camera. Use the spudger tool to carefully pry the grip from the rest of the camera. Use the spudger tool to carefully pry the grip from the rest of the camera.
  • Use the spudger tool to carefully pry the grip from the rest of the camera.

コメントを追加する

Once the grip is loose, use your fingers to remove it from the camera.
  • Once the grip is loose, use your fingers to remove it from the camera.

コメントを追加する

Remove the 4.8mm (.19in) long silver screw from the inside of the grip.
  • Remove the 4.8mm (.19in) long silver screw from the inside of the grip.

コメントを追加する

Remove the hinge of the battery door from the inside of the grip. Our sample camera's battery door was broken off of its hinge. Picture two shows an example of a battery door that is not broken.
  • Remove the hinge of the battery door from the inside of the grip.

  • Our sample camera's battery door was broken off of its hinge. Picture two shows an example of a battery door that is not broken.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Daniel Bussone

メンバー登録日: 2011年01月28日

1,206 ポイント

11のガイドは作成済み

チーム

Cal Poly, Team 3-41, Regan Winter 2011 Cal Poly, Team 3-41, Regan Winter 2011人のメンバー

CPSU-REGAN-W11S3G41

2 メンバー

11のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 3,880