Digital2 D2-861G Charging Port Replacement - iFixit 修理ガイド

この修理ガイドは変更されています。最新の未承認バージョンに切り替えます。

はじめに

This guide will be showing you how to replace the charging port for the Digital2 D2-861G model. Be sure to carefully remove parts to avoid damaging the device.

必要な工具と部品

手順1 Motherboards

Digital2 D2-861G Charging Port Replacement, Motherboards: 手順 1、 1の画像 1

Working on your device while powered on may result in electric shock. Make sure to unplug and power down your device before you begin.
Place your device on a soft cloth to avoid scratching the screen.
Flip your device over so back panel is facing upwards.

手順2

Digital2 D2-861G Charging Port Replacement: 手順 2、 1の画像 1

Do not use a lot of force as it can break the clips or the back panel.
Insert spudger in the slot below the micro SD card.
You should hear clips releasing as you pry along the edges.
With the spudger tool, run along the edges of the backing undoing 20 plastic clips.

手順3

Digital2 D2-861G Charging Port Replacement: 手順 3、 3の画像 1

Digital2 D2-861G Charging Port Replacement: 手順 3、 3の画像 2

Digital2 D2-861G Charging Port Replacement: 手順 3、 3の画像 3

Locate the gold colored ZIF (Zero insertion force) connector and disconnect it from the motherboard.
To disconnect the ZIF connector, go under the black tab and lift up. Then pull the connector out.
Locate the bundled cable connector and disconnect it by simply pulling it gently or using a spudger.
Disconnecting the bundled cable connector helps avoid short circuiting anything on the device.

手順4

Digital2 D2-861G Charging Port Replacement: 手順 4、 3の画像 1

Digital2 D2-861G Charging Port Replacement: 手順 4、 3の画像 2

Digital2 D2-861G Charging Port Replacement: 手順 4、 3の画像 3

Make sure to have your magnetic board to hold your screws.
Remove two 3.51mm screws that are located on the top corners with your Phillips #00 screwdriver.
Next, unplug the ZIF connector by going under the black tab and simply lift up.
Slide the connector out with the pointed side of the spudger.

手順5

Digital2 D2-861G Charging Port Replacement: 手順 5、 3の画像 1

Digital2 D2-861G Charging Port Replacement: 手順 5、 3の画像 2

Digital2 D2-861G Charging Port Replacement: 手順 5、 3の画像 3

This step is optional if you want to remove the metal casing.
Insert the pointed side of the spudger in the corner and gently lift.
Once one side is lifted, use your fingers and with little force, lift up to remove the case.

手順6

Digital2 D2-861G Charging Port Replacement: 手順 6、 1の画像 1

Use little force or else you risk breaking the motherboard.
Watch out for the ZIF connector!
There is a white clip holding the motherboard.
To remove the motherboard, grab the component on the top left and gently lift while pushing or pulling to the right.

手順7 Charging Port

Digital2 D2-861G Charging Port Replacement, Charging Port: 手順 7、 1の画像 1

Refer to iFixit's guide on how to Solder はんだ付けとはんだ除去の作業ガイド
To replace the charging port, you can either replace the motherboard or desolder the port.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Eduardo Duran

メンバー登録日: 09/29/16

600 ポイント

5のガイドは作成済み

+9 個以上のバッジ

チーム

Eastern Washington University, Team 1-3, Crane Fall 2016 Eastern Washington University, Team 1-3, Crane Fall 2016人のメンバー

EWU-CRANE-F16S1G3

3 メンバー

6のガイドは作成済み

0 件のコメント

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 237