はじめに

Remove the Motherboard from the computer.

パーツ

パーツは必要ありません。

Make sure the computer is turned off, by selecting the start menu and choosing “Shut Down”.
  • Make sure the computer is turned off, by selecting the start menu and choosing “Shut Down”.

  • Ensure all cables, speakers and other devices are unplugged and turned off before opening the computer case.

コメントを追加する

Lay the computer on its side; you will see a blue knob. Turn this knob 90 deg clockwise.
  • Lay the computer on its side; you will see a blue knob.

  • Turn this knob 90 deg clockwise.

コメントを追加する

Slide the panel case forward about 1/2 inch while knob is turned. Lift panel case off computer.
  • Slide the panel case forward about 1/2 inch while knob is turned.

  • Lift panel case off computer.

コメントを追加する

Remove the large blue cover from the computer, there are no screws or tabs keeping it in place. Remove the large blue cover from the computer, there are no screws or tabs keeping it in place.
  • Remove the large blue cover from the computer, there are no screws or tabs keeping it in place.

コメントを追加する

Press down on the release tab above the heat sink. Press down on the release tab above the heat sink.
  • Press down on the release tab above the heat sink.

コメントを追加する

Pull the heat sink out of the computer while pressing on the release tab. When reassembling make sure to clean the processor and heat sink of all old thermal paste and apply new paste to the processor
  • Pull the heat sink out of the computer while pressing on the release tab.

  • When reassembling make sure to clean the processor and heat sink of all old thermal paste and apply new paste to the processor

コメントを追加する

Remove the power supply that connects the upper fan to the motherboard. The power supply has black, red, green and yellow wires. Remove the power supply that connects the upper fan to the motherboard. The power supply has black, red, green and yellow wires.
  • Remove the power supply that connects the upper fan to the motherboard. The power supply has black, red, green and yellow wires.

コメントを追加する

Remove the rubber grommets from the base of the fan. A spudger may be useful. Remove the rubber grommets from the base of the fan. A spudger may be useful.
  • Remove the rubber grommets from the base of the fan. A spudger may be useful.

コメントを追加する

Press on the blue release tab and pull the upper fan out of the computer. Press on the blue release tab and pull the upper fan out of the computer.
  • Press on the blue release tab and pull the upper fan out of the computer.

コメントを追加する

Remove the power supply that connects the lower fan to the motherboard, distinguished by it's black, red, green and yellow wires. Make sure to press on the release tab while removing the power connector.
  • Remove the power supply that connects the lower fan to the motherboard, distinguished by it's black, red, green and yellow wires.

  • Make sure to press on the release tab while removing the power connector.

コメントを追加する

Remove the rubber grommets from the base of the fan. A spudger may be useful. Remove the rubber grommets from the base of the fan. A spudger may be useful.
  • Remove the rubber grommets from the base of the fan. A spudger may be useful.

コメントを追加する

Press on the blue release tab and remove the fan. Press on the blue release tab and remove the fan.
  • Press on the blue release tab and remove the fan.

コメントを追加する

The RAM are the two green cards in the corner of the computer.
  • The RAM are the two green cards in the corner of the computer.

  • At each end of the card, there are two white clips securing the RAM to the Motherboard.

コメントを追加する

Push down both white clips with your thumbs until you hear a click. The RAM cards can now be removed.
  • Push down both white clips with your thumbs until you hear a click.

  • The RAM cards can now be removed.

コメントを追加する

Unplug the blue cable that connects the hard drive to the motherboard. Unplug the blue cable that connects the hard drive to the motherboard.
  • Unplug the blue cable that connects the hard drive to the motherboard.

コメントを追加する

Unplug the power supply, distinguished by its red and yellow wires.
  • Unplug the power supply, distinguished by its red and yellow wires.

コメントを追加する

Squeeze the release tabs on either side of the hard drive.
  • Squeeze the release tabs on either side of the hard drive.

  • Then slide the hard drive out of the computer while squeezing the tabs.

コメントを追加する

Unplug the cable that connects the hard drive to the Motherboard.
  • Unplug the cable that connects the hard drive to the Motherboard.

コメントを追加する

Press on the release tab and remove the motherboard speaker which is attached to the side of the tower. Press on the release tab and remove the motherboard speaker which is attached to the side of the tower.
  • Press on the release tab and remove the motherboard speaker which is attached to the side of the tower.

コメントを追加する

Unplug the power cable attached to the motherboard speaker.
  • Unplug the power cable attached to the motherboard speaker.

  • Make sure to press on the release tab while removing the power cable.

コメントを追加する

Remove four screws located at the back of the computer tower. Remove four screws located at the back of the computer tower.
  • Remove four screws located at the back of the computer tower.

コメントを追加する

Carefully detach the motherboard from the computer case.
  • Carefully detach the motherboard from the computer case.

コメントを追加する

Lift the motherboard from the rest of the computer case.
  • Lift the motherboard from the rest of the computer case.

Thanks a lot :)

foundedger - 返信

Hi,

Excellent guide.

I have one of these, and i was thinking of opening it up.

Its sound output disappeared one day. Quite unexpectedly.

No reason that i could see. Couldn't find anything in the

settings to make it go again.

Finally i thought that maybe its 'sound card' had gotten

jogged, or maybe loose, and needed 're-seating'.

After reading through your article on the SX-280,

i now see that it has no 'sound card'.

It has 'on-board' sound facilities.

So for me that has pros and cons.

Pros, i dont need to look for a sound card to re-seat it.

Cons, i dont know what to do about my lost sound now.

As to updating the images, i think they are appropriately

dated to suit this model of PC.

Pre-Requisites ... Not quite sure what this refers to.

Maybe a phillips screwdriver is a prerequisite.

Maybe i missed something, but i dont see that newer pics

would help at all, but the poster is quite correct about

this guide, it is very good.

Regards, John :)

John - 返信

REal nice writeup, saved me a lot of guesswork. Thanks a lot.

JA Reyes, MArch 30, 2015.

Jose Reyes - 返信

Fan closer to heat sink

No need to remove rubber grommets. After pressing blue tap, fan can be moved sideways, towards housing, after about 2 to 3 mmm travel the slots that hold it become wider, and fan, plus blue plastic bracket can be lifted out.

Same is true for other fan, but more difficult to slide. This fan does not have

to be removed to get motherboard out.

Dieter Ast - 返信

Unplug the cable that powers the hard drive, which has orange, red and yellow wires.
  • Unplug the cable that powers the hard drive, which has orange, red and yellow wires.

  • Make sure to press the release tab while removing the cable.

コメントを追加する

Unplug the cable that powers the emergency shut off, distinguished by its red wires. Make sure to press on the release tab while removing the emergency shut off.
  • Unplug the cable that powers the emergency shut off, distinguished by its red wires.

  • Make sure to press on the release tab while removing the emergency shut off.

コメントを追加する

Remove two screws from the Hard Drive Stand. Remove two screws from the Hard Drive Stand.
  • Remove two screws from the Hard Drive Stand.

コメントを追加する

Slide the Hard Drive Stand to left side. Remove the stand from the rest of the rear panel.
  • Slide the Hard Drive Stand to left side.

  • Remove the stand from the rest of the rear panel.

コメントを追加する

Remove the studs that support the Hard Drive Stand from the motherboard. The studs can be removed by hand.
  • Remove the studs that support the Hard Drive Stand from the motherboard.

  • The studs can be removed by hand.

コメントを追加する

Remove the four screws located on heat sink stand. The heat sink stand can now be lifted from the motherboard. The heat sink stand can now be lifted from the motherboard.
  • Remove the four screws located on heat sink stand.

  • The heat sink stand can now be lifted from the motherboard.

コメントを追加する

Remove the four screws holding the motherboard to the rear computer panel. Remove the four screws holding the motherboard to the rear computer panel.
  • Remove the four screws holding the motherboard to the rear computer panel.

コメントを追加する

The motherboard can now be removed from the remaining panel. The motherboard can now be removed from the remaining panel.
  • The motherboard can now be removed from the remaining panel.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

10 の人々がこのガイドを完成させました。

Tom

メンバー登録日: 2010年10月04日

799 ポイント

7のガイドは作成済み

チーム

Cal Poly, Team 22-4, Maness Fall 2010 Cal Poly, Team 22-4, Maness Fall 2010人のメンバー

CPSU-MANESS-F10S22G4

4 メンバー

13のガイドは作成済み

Good job. Thanks for sharing, friend.

Angel Peguero - 返信

Great guide! I got stuck at the Mobo tray, I knew the black screws were involved but couldn't get it with out help. Thanks!

Fans can be removed with board tray, otherwise they're getting pulled off their rubber isolating feet. Once out with the mobo, the fans slide off the board tray with their plastic shoes attached.

purchases - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 9

過去 30 日: 19

今までの合計 17,930