メインコンテンツにスキップ

はじめに

The motherboard replacement for the OptiPlex FX170, compared to other computers, is actually rather painless. One should, however, be familiar with preventing electro-static dischage (ESD) damage to electronics.

  1. With the base stand facing upwards, unscrew the 6mm Phillips #2 screw.
    • With the base stand facing upwards, unscrew the 6mm Phillips #2 screw.

    • Pull the base stand straight up from the device.

  2. Unscrew and remove the eight 4mm Phillips #0 screws (four on top, four on bottom) from the top and bottom of the device. Unscrew and remove the eight 4mm Phillips #0 screws (four on top, four on bottom) from the top and bottom of the device.
    • Unscrew and remove the eight 4mm Phillips #0 screws (four on top, four on bottom) from the top and bottom of the device.

  3. Run the flat side of the spudger along the entire line of the case starting from the back where the power plug and a small screw are located. Use care to not apply excessive force that could damage retaining clips while running the spudger along the case. Use care to not apply excessive force that could damage retaining clips while running the spudger along the case.
    • Run the flat side of the spudger along the entire line of the case starting from the back where the power plug and a small screw are located.

    • Use care to not apply excessive force that could damage retaining clips while running the spudger along the case.

  4. Once the clips have been released, gently disengage the cover from the rest of case by pulling in opposite directions. Once the clips have been released, gently disengage the cover from the rest of case by pulling in opposite directions.
    • Once the clips have been released, gently disengage the cover from the rest of case by pulling in opposite directions.

  5. PCラップトップ用バッテリー

    An easy fix for a big power boost.

    ショップを見る

    PCラップトップ用バッテリー

    An easy fix for a big power boost.

    ショップを見る
  6. Using fingers, push the clips on either side of the RAM. The RAM will pop up at a 45 degree angle when both clips are disengaged. Using fingers, push the clips on either side of the RAM. The RAM will pop up at a 45 degree angle when both clips are disengaged.
    • Using fingers, push the clips on either side of the RAM. The RAM will pop up at a 45 degree angle when both clips are disengaged.

  7. Lift and pull out the RAM.
    • Lift and pull out the RAM.

  8. Using the spudger, gently push on the underside of the memory board to loosen it. Gently grasp each side and pull up to release the memory board.
    • Using the spudger, gently push on the underside of the memory board to loosen it. Gently grasp each side and pull up to release the memory board.

  9. To remove the battery, pull up on the connector that is plugged into the motherboard.
    • To remove the battery, pull up on the connector that is plugged into the motherboard.

  10. Remove the two 4mm Phillips #00 screws that are along the back of the case. Remove the two 4mm Phillips #00 screws that are along the back of the case.
    • Remove the two 4mm Phillips #00 screws that are along the back of the case.

  11. Remove the two foam bumpers that lie on top of the two front USB ports with fingers. Do not throw them away.
    • Remove the two foam bumpers that lie on top of the two front USB ports with fingers. Do not throw them away.

  12. Disconnect the speaker cable from the motherboard by gently pulling it straight up to disengage it from the port. Remove the four 4mm Philips #0 screws that secure the motherboard to the case.
    • Disconnect the speaker cable from the motherboard by gently pulling it straight up to disengage it from the port.

    • Remove the four 4mm Philips #0 screws that secure the motherboard to the case.

    • The screw in the corner where the RAM is located is covered by a small piece of Mylar tape, peel this tape back to reveal the screw. The tweezers can be helpful for this.

  13. Gently grasp the motherboard by the heat sink (the black finned piece). Lift the motherboard at an angle such that the ports along the back side come up first. Continue lifting the motherboard, then slowly tilt the piece off to the right to break the Mylar tape over the front USB ports. Be careful when handling the motherboard to prevent electro-static discharge (ESD) damage. If the motherboard is being removed as part of a prerequisite, place the motherboard into a bag designed to prevent a build up of a static charge (usually referred to as a static bag).
    • Gently grasp the motherboard by the heat sink (the black finned piece). Lift the motherboard at an angle such that the ports along the back side come up first.

    • Continue lifting the motherboard, then slowly tilt the piece off to the right to break the Mylar tape over the front USB ports.

    • Be careful when handling the motherboard to prevent electro-static discharge (ESD) damage. If the motherboard is being removed as part of a prerequisite, place the motherboard into a bag designed to prevent a build up of a static charge (usually referred to as a static bag).

まとめ

To reassemble your device, follow these instructions in reverse order.

Frank Pecka

メンバー登録日: 2015年01月13日

340 ポイント

3のガイドは作成済み

チーム

Eastern Washington University, Team 1-4, Carnegie Winter 2015 Eastern Washington University, Team 1-4, Carnegie Winter 2015人のメンバー

EWU-CARNEGIE-W15S1G4

3 メンバー

13のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 11

今までの合計 954