メインコンテンツにスキップ

このバージョンは誤った内容を含んでいる可能性があります。最新の承認済みスナップショットに切り替えてください。

必要な工具と部品

  1. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 1、 1の画像 1
    • Disconnect the Laptop from the AC adapter and turn off the Laptop.

  2. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 2、 1の画像 1
    • Place laptop so the bottom faces up.

  3. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 3、 3の画像 1 : 手順 3、 3の画像 2 : 手順 3、 3の画像 3
    • Remove the silver 15mm PH1 screw that holds the plastic cover in place over the battery.

    • Remove the 8mm PH 1 screw that holds the plastic cover in place over the battery.

    • Place the screws accordingly because the length of the screws will matter when you reassemble.

  4. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 4、 1の画像 1
    • Using a metal jimmy, pry up to remove the first half of the cover.

  5. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 5、 1の画像 1
    • Apply pressure using your fingertips on the top of the cover, pushing to the front of the laptop. This will make the plate slide off exposing the hard drive.

  6. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 6、 3の画像 1 : 手順 6、 3の画像 2 : 手順 6、 3の画像 3
    • Remove the three black PH1 6mm screws that anchor the hard drive.

    • This screw hole will be empty because the 15mm silver screw that holds the plastic cover will anchor the hard drive down.

  7. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 7、 1の画像 1
    • Using the Jimmy, pry up the hard drive and lift out using your fingers.

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 1の画像 1
    • Gently wiggle and pull the connector to disconnect the Seta Cable attaching the hard drive to the laptop.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 3の画像 1 : 手順 9、 3の画像 2 : 手順 9、 3の画像 3
    • Remove the harness around the hard drive by removing four black 4mm PH1 screws located on the side.

  10. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 10、 1の画像 1
    • Remove the hard drive from the harness.

ゴール

2 の人々がこのガイドを完成させました。

作成者

5人の作成者と共同で作成されました。

Joshua Plagerman

メンバー登録日: 09/26/18

735 ポイント

4のガイドは作成済み

チーム

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 9

過去 30 日: 10

今までの合計 1,256