危険
潜在的な危険
この手順に正しく従わない場合は損傷が生じる可能性があります。ご注意のうえ使用し、すべての警告に従ってください。
危険

はじめに

Following this guide involves completely disassembling the monitor. This process isn't terribly difficult, just time consuming.

Carefully place the monitor face down on a flat surface, being careful to protect the display.
  • Carefully place the monitor face down on a flat surface, being careful to protect the display.

  • Remove the four 10 mm Phillips #2 screws from the back panel.

コメントを追加する

Flip the monitor back over, so that the display is facing you.
  • Flip the monitor back over, so that the display is facing you.

  • Use a spudger to remove the front bezel by unsnapping it in a counter clockwise fashion, starting at the bottom right, and ending at the button panel.

コメントを追加する

Slowly unsnap the bezel around the buttons.
  • Slowly unsnap the bezel around the buttons.

  • Be careful to not fully remove the bezel here, because a ribbon cable attaches the buttons to the monitor.

コメントを追加する

Carefully flip the monitor back over, making sure to keep the front bezel in place.
  • Carefully flip the monitor back over, making sure to keep the front bezel in place.

  • Lift the back cover off of the rest of the monitor.

コメントを追加する

Locate the USB port cover on the right hand side of the monitor. Remove the one 5 mm Phillips #2 screw. Remove the USB port cover by sliding it out and away from the monitor.
  • Locate the USB port cover on the right hand side of the monitor.

  • Remove the one 5 mm Phillips #2 screw.

  • Remove the USB port cover by sliding it out and away from the monitor.

コメントを追加する

Disconnect the USB ports by gentling grasping and pulling on the connector. Disconnect the USB ports by gentling grasping and pulling on the connector.
  • Disconnect the USB ports by gentling grasping and pulling on the connector.

コメントを追加する

Remove the five 5 mm Phillips #2 screws from the back panel.
  • Remove the five 5 mm Phillips #2 screws from the back panel.

コメントを追加する

Remove the four 4 mm Phillips #2 screws that secure the monitor mount release mechanism to the panel. Set this mechanism off to the side, taking care to keep it all in one piece.
  • Remove the four 4 mm Phillips #2 screws that secure the monitor mount release mechanism to the panel.

  • Set this mechanism off to the side, taking care to keep it all in one piece.

コメントを追加する

Use a 5 mm nut driver to remove the four 12 mm standoff screws securing the video connectors to the panel. Use a 5 mm nut driver to remove the four 12 mm standoff screws securing the video connectors to the panel.
  • Use a 5 mm nut driver to remove the four 12 mm standoff screws securing the video connectors to the panel.

コメントを追加する

Use the tweezers to lift up the seven security tabs that secure the back panel to the rest of the monitor. If the security tabs are held down too tightly, use the spudger to pry them up, and then finish them off with the tweezers.
  • Use the tweezers to lift up the seven security tabs that secure the back panel to the rest of the monitor.

  • If the security tabs are held down too tightly, use the spudger to pry them up, and then finish them off with the tweezers.

コメントを追加する

Lift up on the back panel to remove it from the rest of the monitor. Be careful when doing so, as the edges of the back panel can be very sharp. Be careful when doing so, as the edges of the back panel can be very sharp.
  • Lift up on the back panel to remove it from the rest of the monitor.

  • Be careful when doing so, as the edges of the back panel can be very sharp.

コメントを追加する

Use the tweezers to remove the four connectors from the power supply board. The power supply has several large capacitors (they look like little cylinders), that can shock you if they discharge. Be careful not to touch them as you continue to work.
  • Use the tweezers to remove the four connectors from the power supply board.

  • The power supply has several large capacitors (they look like little cylinders), that can shock you if they discharge. Be careful not to touch them as you continue to work.

コメントを追加する

Remove the five 7 mm Phillips #2 screws from the power supply board.
  • Remove the five 7 mm Phillips #2 screws from the power supply board.

コメントを追加する

Open up the clip securing the wires running between the power supply and video boards. Gently remove the connector running from the video board to the power supply board.
  • Open up the clip securing the wires running between the power supply and video boards.

  • Gently remove the connector running from the video board to the power supply board.

コメントを追加する

The power supply board can now be removed. The power supply board can now be removed.
  • The power supply board can now be removed.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Geoff Wacker

メンバー登録日: 2013年09月30日

69,133 ポイント

143のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 10

過去 30 日: 68

今までの合計 2,414