メインコンテンツにスキップ

DeWalt DW660 Bearings Replacement

必要な工具と部品

  1. DeWalt DW660 Bearings Replacement, Bearings: 手順 1、 1の画像 1
    • Pull off the depth guide.

    • If the guide doesn't come away easily, use a twisting motion to pull it from the tool.

  2. DeWalt DW660 Bearings Replacement: 手順 2、 3の画像 1 DeWalt DW660 Bearings Replacement: 手順 2、 3の画像 2 DeWalt DW660 Bearings Replacement: 手順 2、 3の画像 3
    • Hold down lock #1 to prevent the motor from spinning.

    • While holding lock #1, hold down lock #2 as well.

    • Rotate lock #2 counterclockwise to unscrew the collet nut.

  3. DeWalt DW660 Bearings Replacement: 手順 3、 1の画像 1
    • Remove the collet nut and the collet from the device.

  4. DeWalt DW660 Bearings Replacement: 手順 4、 2の画像 1 DeWalt DW660 Bearings Replacement: 手順 4、 2の画像 2
    • Unscrew the four 19mm T20 Torx screws on the motor shroud.

    • Carefully remove the shroud from the body.

    • When removing the shroud, the spring that operates lock #2 may pop out.

  5. DeWalt DW660 Bearings Replacement: 手順 5、 3の画像 1 DeWalt DW660 Bearings Replacement: 手順 5、 3の画像 2 DeWalt DW660 Bearings Replacement: 手順 5、 3の画像 3
    • Unscrew the four 19mm T20 Torx screws on the side of the back end of the DW660.

    • Take apart the back two halves.

    • Using two fingers, pull the black and white power wires from the motor to completely disconnect the back half of the device.

  6. DeWalt DW660 Bearings Replacement: 手順 6、 2の画像 1 DeWalt DW660 Bearings Replacement: 手順 6、 2の画像 2
    • Lift the coiled spring from the back of the brush using a spudger.

    • While holding the spring out of the way, use a pointed spudger to slide the carbon brush up out of the guide.

    • Slowly release the brush spring. It will sit in the brush guide.

    • Repeat this step for the second brush.

  7. DeWalt DW660 Bearings Replacement: 手順 7、 1の画像 1
    • Pull the rotor out of the front of the DW660.

    • Be very careful to make sure the rotor does not collide with the stator. The stator coils or the commutator can be damaged very easily.

  8. DeWalt DW660 Bearings Replacement: 手順 8、 1の画像 1
    • Remove the snap ring from the bearing by using snap ring pliers.

    • This will take some force and the snap ring will act as a spring, so be careful to make sure the ring does not fly off the pliers.

  9. DeWalt DW660 Bearings Replacement: 手順 9、 1の画像 1
    • Pull the black plastic bearing block off of the motor shaft.

    • Remove the ball bearing from the bearing block.

  10. DeWalt DW660 Bearings Replacement: 手順 10、 2の画像 1 DeWalt DW660 Bearings Replacement: 手順 10、 2の画像 2
    • Remove the rubber cap from the bearing.

    • Use the bearing puller to remove the bearing from the shaft.

    • When installing the new bearings, it may help to use a small hammer and a hollow circular pipe with the same outer diameter as the inner ring of the bearing.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Ryan Owen Rheaume

メンバー登録日: 04/03/15

405 ポイント

1ガイドが承認済み

チーム

UMass Dartmouth, Team 2-7, Isaacson Spring 2016 UMass Dartmouth, Team 2-7, Isaacson Spring 2016人のメンバー

UMASSD-ISAACSON-S16S2G7

3 メンバー

5のガイドは作成済み

コメント 1 件

What size bearing does it take?

James Armstrong - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 5

今までの合計 787