修理を始めるには コミュニティ ストア

DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement

はじめに

The Con Board is located under the back cover. This guide will help you remove and replace the Back Con Board from your DJI Phantom 4 Advanced Remote Controller.

Many issues that arise with a DJI Remote Controller are caused by a faulty Back Con Board.

Before beginning, disconnect your drone and power off the remote completely.

必要な工具と部品

  1. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement, Back Panel: 手順 1、 1の画像 1

    • Remove the four screws with a Torx T8 screwdriver to access the back con board.

    編集

  2. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 2、 2の画像 1 DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 2、 2の画像 2

    • Remove three screws using a Phillips #00 screwdriver.

    編集

  3. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 3、 2の画像 1 DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 3、 2の画像 2

    • With tweezers, gently remove the large con board tab.

    • Use your hands to remove the two small clips. Pull out from the socket, in a horizontal direction.

    編集

  5. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 4、 2の画像 1 DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 4、 2の画像 2

    • Peel off the rubber grips to access the screw holes.

    • Make sure to save your grips and do not to get them stuck to anything, you are going to want to save the adhesive.

    • Remove the back board and set it aside.

    編集

  6. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 5、 2の画像 1 DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 5、 2の画像 2

    • Pull apart the back plastic panel.

    • Recommended tool for this would be the metal spudger, but not required.

    • Once the back panel is off, you will have access to the motherboard.

    編集

  7. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement, Back Con Board: 手順 6、 1の画像 1

    • Remove the three PH0 screws securing the PCB to the remote.

    編集

  8. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 7、 2の画像 1 DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 7、 2の画像 2

    • Remove each of the three ribbon cables from their tabs by pulling in a horizontal direction away from the socket.

    • Remove the Back Con Board.

    編集

  9. DJI Phantom 4 Advanced Remote Controller Back Con Board Replacement: 手順 8、 1の画像 1

    • The board can now be replaced.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

6人の作成者と共同で作成されました。

Gunnar Behny

メンバー登録日: 10/02/18

154 ポイント

1ガイドが承認済み

バッジ: 7

+4 個以上のバッジ

チーム

Linn Benton Community College, Team S1-G4, Johnson Fall 2018 Linn Benton Community College, Team S1-G4, Johnson Fall 2018人のメンバー

LBCC-JOHNSON-F18S1G4

3 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 9

今までの合計 960