修理を始めるには

修理する権利

ストア

Cuisinart Smart Stick CSB-75 Motor Replacement

作成者： Jordan Robinson (そして 4 人のその他投稿者)
  • コメント: 0
  • お気に入り: 0
  • 完了: 4

難易度

難しい

手順

5

所要時間

1時間

セクション

1

フラグ

0

はじめに

This guide will teach you how to replace the motor inside your Cuisinart Smart Stick. If power is not being supplied to the Smart Stick, the motor could be unresponsive.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Located on the back of the motor body are three screw covers. To remove the three grey screw covers, use a Flat Head Screwdriver (1.0mm or 1.5mm). After prying these off, the screws will be exposed. After prying these off, the screws will be exposed.

    • Located on the back of the motor body are three screw covers. To remove the three grey screw covers, use a Flat Head Screwdriver (1.0mm or 1.5mm).

    • After prying these off, the screws will be exposed.

    編集

  2. Remove three 13.3 mm Phillips PH#2 screws. Remove three 13.3 mm Phillips PH#2 screws.

    • Remove three 13.3 mm Phillips PH#2 screws.

    編集

  4. Pry open Cuisinart using a plastic opening tool. The metal spudger is great when you need serious prying power, but the regular black nylon spudger or a plastic opening tool should be used whenever possible. Make sure to pry open near the clips of the smart stick for easy opening.

    • Pry open Cuisinart using a plastic opening tool.

    • The metal spudger is great when you need serious prying power, but the regular black nylon spudger or a plastic opening tool should be used whenever possible.

    • Make sure to pry open near the clips of the smart stick for easy opening.

    編集

  5. Unscrew the 4 screws on inside. Remove 2 13.3mm Phillips PH#2 screws. Remove 2 17.5 mm Phillips PH#2 screws.

    • Unscrew the 4 screws on inside.

    • Remove 2 13.3mm Phillips PH#2 screws.

    • Remove 2 17.5 mm Phillips PH#2 screws.

    • Unscrewing these screws will isolate the motor.

    編集

  6. Refer to these steps on Soldering to replace the motor in the smart stick. Be careful when soldering; it gets very hot. Be careful when soldering; it gets very hot.

    • Refer to these steps on Soldering to replace the motor in the smart stick.

    • Be careful when soldering; it gets very hot.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

作成者

4他の投稿者と一緒に

Jordan Robinson

メンバー登録日: 2015年09月02日

527 ポイント

4のガイドは作成済み

バッジ: 9

+6 個以上のバッジ

チーム

USF Tampa, Team 16-2, Wollert Fall 2015 USF Tampa, Team 16-2, Wollert Fall 2015人のメンバー

USFT-WOLLERT-F15S16G2

4 メンバー

4のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 2

過去 7 日: 13

過去 30 日: 76

今までの合計 4,467