メインコンテンツにスキップ

Cirago M9030 IDE Connector Replacement

必要な工具と部品

  1. Cirago M9030 IDE Connector Replacement, Cover: 手順 1、 1の画像 1
    • Use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the top of the cover.

  2. Cirago M9030 IDE Connector Replacement: 手順 2、 1の画像 1
    • Similar to the last step, flip the cover over and use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the bottom of the cover.

    • Remove the warranty sticker across the bottom.

  3. Cirago M9030 IDE Connector Replacement: 手順 3、 2の画像 1 Cirago M9030 IDE Connector Replacement: 手順 3、 2の画像 2
    • Gently take the cover apart using your hands separating the top and bottom.

    • The outer shell is expected to easily come apart.

  4. Cirago M9030 IDE Connector Replacement, Hard Drive: 手順 4、 1の画像 1
    • Make sure that the screen of the device is facing down.

  5. Cirago M9030 IDE Connector Replacement: 手順 5、 3の画像 1 Cirago M9030 IDE Connector Replacement: 手順 5、 3の画像 2 Cirago M9030 IDE Connector Replacement: 手順 5、 3の画像 3
    • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

    • Raise the bottom edge of the hard drive 15 degrees up from the device.

  6. Cirago M9030 IDE Connector Replacement: 手順 6、 3の画像 1 Cirago M9030 IDE Connector Replacement: 手順 6、 3の画像 2 Cirago M9030 IDE Connector Replacement: 手順 6、 3の画像 3
    • Place fingers on the IDE connectors gently picking up and sliding the hard drive out from the IDE module.

  7. Cirago M9030 IDE Connector Replacement, IDE Connector: 手順 7、 2の画像 1 Cirago M9030 IDE Connector Replacement, IDE Connector: 手順 7、 2の画像 2
    • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard located at the top.

  8. Cirago M9030 IDE Connector Replacement: 手順 8、 1の画像 1
    • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

  9. Cirago M9030 IDE Connector Replacement: 手順 9、 2の画像 1 Cirago M9030 IDE Connector Replacement: 手順 9、 2の画像 2
    • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

    • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

  10. Cirago M9030 IDE Connector Replacement: 手順 10、 1の画像 1
    • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

  11. Cirago M9030 IDE Connector Replacement: 手順 11、 2の画像 1 Cirago M9030 IDE Connector Replacement: 手順 11、 2の画像 2
    • Completely remove the IDE connector from the device.

    • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

7人の作成者と共同で作成されました。

Ryan Sutardji

メンバー登録日: 06/29/12

171 ポイント

7のガイドは作成済み

チーム

Cal Poly, Team 1-4, Regan SU 2012 Cal Poly, Team 1-4, Regan SU 2012人のメンバー

CPSU-REGAN-SU12S1G4

4 メンバー

7のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 963