パーツ

パーツは必要ありません。

  • Hold the phone with the back (camera side) facing you. Slide the battery cover off of the phone.

コメントを追加する

  • Pull the battery out by lifting the black tab on the left side of the battery.

コメントを追加する

  • Remove the camera cover of the phone, using your light blue wedge tool.

コメントを追加する

  • Unscrew the four black Torx head screws, found in each corner of the back.

  • Warning: Unscrewing the screw indicated in the picture will void any warranty on the phone.

コメントを追加する

Unscrew the black Phillips head screw below the right speaker.
  • Unscrew the black Phillips head screw below the right speaker.

コメントを追加する

  • After removing the screw, pull up on the motherboard to release it from the circuit board (green tab, see Figure 11). This will simply snap out, and does not require too much force.

コメントを追加する

Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.
  • Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.

コメントを追加する

Remove the four silver Phillips head screws from the screened half of the phone.
  • Remove the four silver Phillips head screws from the screened half of the phone.

コメントを追加する

Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.
  • Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Unscrew the four Phillips head screws that attach the screen to the front case.
  • Unscrew the four Phillips head screws that attach the screen to the front case.

コメントを追加する

  • Remove the circuit board; pull it apart at the orange tab. This will detach the screen from its circuit board.

コメントを追加する

Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.
  • Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.

コメントを追加する

  • Place screen back into front cover.

コメントを追加する

  • Screw the four smallest silver Torx head screws into the circuit board, which will attach it to the front cover.

コメントを追加する

  • Feed the circuit board through the back piece.

コメントを追加する

  • Use the four Phillips head silver screws to attach the back piece to the front of the phone.

コメントを追加する

Slide the circuit board through the slot in the keyboard.
  • Slide the circuit board through the slot in the keyboard.

コメントを追加する

  • Attach the keyboard to the sliding tracks using the four silver Torx screws.

コメントを追加する

Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.
  • Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.

コメントを追加する

Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.
  • Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.

コメントを追加する

  • Place the back cover onto the motherboard, clicking it into place.

コメントを追加する

Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.
  • Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.

コメントを追加する

Replace the camera cover.
  • Replace the camera cover.

コメントを追加する

Replace battery, keeping the black tab available to grab.
  • Replace battery, keeping the black tab available to grab.

コメントを追加する

Slide the battery cover back into place.
  • Slide the battery cover back into place.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Laura Kimberly Simonds

メンバー登録日: 2012年09月24日

301 ポイント

3のガイドは作成済み

チーム

University of Maine, Team 1-1, Diaz Fall 2012 University of Maine, Team 1-1, Diaz Fall 2012人のメンバー

UMAINE-DIAZ-F12S1G1

4 メンバー

3のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 2

今までの合計 351