修理を始めるには コミュニティ ストア

Canon Powershot SX30 IS Back Camera Housing Replacement

はじめに

Quick guide on removing and replacing the plastic back cover. Replacement is required if the functions buttons fail to work, or the casing has been damaged.

必要な工具と部品

  1. Canon Powershot SX30 IS Back Camera Housing Replacement, Back Camera Housing: 手順 1、 2の画像 1 Canon Powershot SX30 IS Back Camera Housing Replacement, Back Camera Housing: 手順 1、 2の画像 2

    • Position the camera so that the right side is visible as shown.

    • Unscrew the two 6 mm screws shown using a screwdriver.

    編集

  2. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 2、 3の画像 1 Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 2、 3の画像 2 Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 2、 3の画像 3

    • Remove the plastic flap by pressing down on the center of the hinge and pulling on the flap with the spudger.

    • Then, unscrew the lone 6mm screw that was under the plastic flap.

    編集

  3. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 3、 2の画像 1 Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 3、 2の画像 2

    • Turn the camera so that the bottom is visible, as shown.

    • Unscrew the three 4mm screws shown red using a screwdriver.

    • Unscrew the single 6mm screw.

    • Do not touch the screw shown yellow, removal is unnecessary. (Note: the top right yellow screw should be removed)

    編集

  5. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 4、 1の画像 1

    • Turn the camera so the back side is visible, as shown.

    • Unscrew the two 6mm screws.

    編集

  6. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 5、 1の画像 1

    • Gently remove the back cover using the spudger.

    • Exercise caution, as the wire inside is fragile.

    編集

  7. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 6、 2の画像 1 Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 6、 2の画像 2

    • Detach the wire by lifting the small black bar that holds it to the main body of the camera.

    編集

  8. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 7、 1の画像 1

    • Attach the new cover onto the camera.

    編集

  9. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 8、 1の画像 1

    • Reattach the wire to your new rear casing.

    編集

  10. Canon Powershot SX30 IS Back Camera Housing Replacement: 手順 9、 1の画像 1

    • Close the back cover, and re-insert appropriate screws.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

10人の作成者と共同で作成されました。

Ellis DeVoe

メンバー登録日: 04/14/15

580 ポイント

5のガイドは作成済み

バッジ: 9

+6 個以上のバッジ

チーム

Cal Poly, Team 5-12, Maness Spring 2015 Cal Poly, Team 5-12, Maness Spring 2015人のメンバー

CPSU-MANESS-S15S5G12

4 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 15

今までの合計 1,322