はじめに

The lens is used for capturing specific scenes and to feed these scenes into the camera.

パーツ

パーツは必要ありません。

Slide grey latch to open the battery compartment. Slide grey latch to open the battery compartment.
  • Slide grey latch to open the battery compartment.

コメントを追加する

Push orange retaining clip to the right to free battery. Push orange retaining clip to the right to free battery.
  • Push orange retaining clip to the right to free battery.

コメントを追加する

Remove battery from the camera.
  • Remove battery from the camera.

コメントを追加する

Remove the lanyard.
  • Remove the lanyard.

コメントを追加する

Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.
  • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

  • Be careful to keep track of the different screw sizes as you proceed with this guide.

コメントを追加する

Remove the single 3.8mm screw from the back face of the camera.
  • Remove the single 3.8mm screw from the back face of the camera.

コメントを追加する

Remove the two 2.3mm screws from the right face of the camera.
  • Remove the two 2.3mm screws from the right face of the camera.

コメントを追加する

Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.
  • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

コメントを追加する

Pull the back face panel away from the front end of the body. This may take some wiggling and force.
  • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

コメントを追加する

Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.
  • Remove the CF card door from the left side of the camera body.

コメントを追加する

Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate. Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.
  • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

コメントを追加する

Remove the front face by sliding it off.
  • Remove the front face by sliding it off.

コメントを追加する

Remove the rubber seal that goes over the right side of the viewfinder.
  • Remove the rubber seal that goes over the right side of the viewfinder.

コメントを追加する

Remove the two 3.9mm screws that retain the laminated cooper sheet.
  • Remove the two 3.9mm screws that retain the laminated cooper sheet.

コメントを追加する

Remove the seven wire connections that connect to the motherboard. Remove the seven wire connections that connect to the motherboard.
  • Remove the seven wire connections that connect to the motherboard.

コメントを追加する

Remove the single 3.8mm screw that is on the motherboard.
  • Remove the single 3.8mm screw that is on the motherboard.

コメントを追加する

Carefully remove the motherboard from the main frame of the camera body.
  • Carefully remove the motherboard from the main frame of the camera body.

コメントを追加する

After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side
  • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

コメントを追加する

Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws
  • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

コメントを追加する

Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly
  • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

  • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

コメントを追加する

Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate
  • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

コメントを追加する

Unsolder the four points at the top of the screen with a soldering iron
  • Unsolder the four points at the top of the screen with a soldering iron

コメントを追加する

  • You do not need to unsolder the screen to get to the lens, but follow the rest of the steps to free the screen from the housing plate.

コメントを追加する

Remove the card-reader shield by removing the screw at the top of the shield.
  • Remove the card-reader shield by removing the screw at the top of the shield.

コメントを追加する

Remove the 2 black screws that attach the battery box to the housing plate. The second picture shows the battery box detached from the housing plate.
  • Remove the 2 black screws that attach the battery box to the housing plate.

  • The second picture shows the battery box detached from the housing plate.

コメントを追加する

Remove the three (3.1mm) black screws that were behind the screen and battery box.
  • Remove the three (3.1mm) black screws that were behind the screen and battery box.

コメントを追加する

Carefully remove the lens. Remove the bottom side of the lens first before the viewfinder side.
  • Carefully remove the lens.

  • Remove the bottom side of the lens first before the viewfinder side.

  • Be careful of wires and delicate parts.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Joseph Melo

メンバー登録日: 2011年04月07日

111 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 20-70, Walters Spring 2011 Cal Poly, Team 20-70, Walters Spring 2011人のメンバー

CPSU-WALTERS-S11S20G70

5 メンバー

4のガイドは作成済み

コメント1件

Camera in the pictures is not Canon Powershot S200

jkovalai - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 5

今までの合計 1,424