メインコンテンツにスキップ

Canon PowerShot SX120 IS Back Cover Replacement

必要な工具と部品

  1. Canon PowerShot SX120 IS Back Cover Replacement, Back Cover: 手順 1、 1の画像 1
    • Turning the camera so the screen is facing you.

    • Remove the two black 3.4 mm screws with a Phillips #00 screwdriver.

  2. Canon PowerShot SX120 IS Back Cover Replacement: 手順 2、 1の画像 1
    • Put the camera with the lens facing up and turn it to the side so the DC IN A/V OUT DIGITAL is facing you.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  3. Canon PowerShot SX120 IS Back Cover Replacement: 手順 3、 2の画像 1 Canon PowerShot SX120 IS Back Cover Replacement: 手順 3、 2の画像 2
    • Put the camera with the lens facing up, and turn it to the side where the battery cover is located.

    • Remove the three black 3.4 mm screws with a Phillips #00 screwdriver.

  4. Canon PowerShot SX120 IS Back Cover Replacement: 手順 4、 2の画像 1 Canon PowerShot SX120 IS Back Cover Replacement: 手順 4、 2の画像 2
    • Put the camera with the lens facing up, turn it to the side where the compartment of the battery (CR1220) for time/date is located.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  5. Canon PowerShot SX120 IS Back Cover Replacement: 手順 5、 1の画像 1
    • Put the camera with the lens facing down, and turn it to the side where the DC IN A/V OUT DIGITAL cover and the silver lanyard attachment are located.

    • Open the DC IN A/V OUT DIGITAL cover.

    • Remove the single black 3.4 mm screw with a Phillips #00 screwdriver.

  6. Canon PowerShot SX120 IS Back Cover Replacement: 手順 6、 3の画像 1 Canon PowerShot SX120 IS Back Cover Replacement: 手順 6、 3の画像 2 Canon PowerShot SX120 IS Back Cover Replacement: 手順 6、 3の画像 3
    • Turn the camera with the lens facing down.

    • Opening the camera can be challenging. Don't get discouraged if it takes you a few tries before the camera is opened.

    • Use the iFixit opening tool to make leverage. Insert the opening tool in the seam where the front case and the back case assemble.

    • Carefully put pressure on the opening tool so the cover can gradually open.

    • Slowly slide the opening tool along the gap and around the edge of the camera.

    • When you are dissembling the back cover, the DC IN A/V OUT DIGITAL cover will also disassemble and fall off.

  7. Canon PowerShot SX120 IS Back Cover Replacement: 手順 7、 1の画像 1
    • Remove the back cover and the DC IN A/V OUT DIGITAL cover from the camera.

終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

8人の作成者と共同で作成されました。

Maria

メンバー登録日: 03/13/14

875 ポイント

1ガイドが承認済み

チーム

New Mexico State, Team 1-3, Easley Spring 2014 New Mexico State, Team 1-3, Easley Spring 2014人のメンバー

NMSU-EASLEY-S14S1G3

4 メンバー

4のガイドは作成済み

コメント 1 件

It took me 2 hours to install the battery door. I dropped one screw and could not find it any more it just vanished.

I was lucky to find one just like the one I lost after a half hour search.All in all I did a pretty good good job for an

auto mechanic .Thanks very much for your help, it was very easy to follow your instructions.

Fred Czarnik

Frederick Czarnik - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 11

今までの合計 1,689