はじめに

This shows how to replace the LCD.

パーツ

パーツは必要ありません。

  1. Unscrew five Phillips screws using a #0 Phillips screwdriver.
    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    コメントを追加する

  2. Open memory card cover by moving the slide switch toward the top end of of the camera.
    • Open memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    コメントを追加する

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    コメントを追加する

    • Unscrew the four Philips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    コメントを追加する

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    コメントを追加する

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    コメントを追加する

    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    コメントを追加する

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    コメントを追加する

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    コメントを追加する

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    コメントを追加する

    • Place the Spludger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    コメントを追加する

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    コメントを追加する

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    コメントを追加する

    • Lift the blue ribbon gate using the Spudger.

    コメントを追加する

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    コメントを追加する

    • Lift the LCD away from the rest of the camera.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Nathan Balcom

メンバー登録日: 2010年01月21日

81 ポイント

8のガイドは作成済み

チーム

Cal Poly, Team 16-28, Maness Winter 2010 Cal Poly, Team 16-28, Maness Winter 2010人のメンバー

CPSU-MANESS-W10S16G28

4 メンバー

8のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 2,851