メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Canon PowerShot A460 Front Casing Replacement

作成者： Alex (そして 6 人のその他投稿者)
  • コメント: 0
  • お気に入り: 0

難易度

簡単

手順

10

所要時間

20分

セクション

2

フラグ

2

Needs More Images

多くの画像が必要

幾つかの画像があればこのガイドの手順がより明確になるでしょう。

Markup Mishap

間違いの指摘

このガイドは最適な校正が必要です。校正の注釈を付けたり訂正することにご協力ください。

はじめに

This guide will guide the user towards removing the front casing and preparing the camera for future repairs.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.

    • Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.

    • While still holding the switch, pull the cover down, allowing it to release and open.

    翻訳

  2. Tilt the camera slightly to allow the batteries to fall out.

    • Tilt the camera slightly to allow the batteries to fall out.

    翻訳

  3. Press on and release the memory card to eject it.

    • Press on and release the memory card to eject it.

    翻訳

  4. Unscrew the 5mm Phillips #00 screw from the bottom of the camera.

    • Unscrew the 5mm Phillips #00 screw from the bottom of the camera.

    • Make sure to keep the different size screws organized to make reassembling the camera simpler.

    翻訳

  6. Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.

    • Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.

    翻訳

  7. Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.

    • Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.

    翻訳

  8. Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.

    • Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.

    翻訳

  9. Remove the second battery cover on the bottom of camera. Take the silver battery out of the camera.

    • Remove the second battery cover on the bottom of camera.

    • Take the silver battery out of the camera.

    翻訳

  10. Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots. Remove the light grey, plastic piece. Remove the plastic portion of the battery flap cover. The metal piece will remain attached.

    • Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots.

    • Remove the light grey, plastic piece.

    • Remove the plastic portion of the battery flap cover. The metal piece will remain attached.

    翻訳

  11. Slightly pull on each side of the camera. It should loosen up and come apart. If it does not pull apart right away, use a little more force. Do not give up!

    • Slightly pull on each side of the camera. It should loosen up and come apart.

    • If it does not pull apart right away, use a little more force.

    • Do not give up!

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

作成者

6他の投稿者と一緒に

Alex

メンバー登録日: 2013年01月18日

67 ポイント

2のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

Cal Poly, Team 19-42, Regan Winter 2013 Cal Poly, Team 19-42, Regan Winter 2013人のメンバー

CPSU-REGAN-W13S19G42

4 メンバー

6のガイドは作成済み

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 1

過去 30 日: 1

今までの合計 553